Search
Filters
Close

WEO006432AWPP3N00000

PMOLED 0.49'' Graphic 64x32, White color, COG, 3V, Interface I2C, Glare (FPC per Soldering)

DESCRIPTION

0.49 inch passive matrix micro OLED display module which is made of 64x32 dots. It has module dimension of 14.5x 11.6 x 1.26 mm and Active Area size 11.18 × 5.58 mm. OLED micro display is built in with SSD1306 IC, it supports I2C interface, 3V power supply. COG structure OLED display which is ultra thin and no need of backlight (self emitting); it's lightweight and low power consumption. This 0.49 inch small sized OLED module is suitable for wearable device, mp3, portable device, personal care appliance, voice recorder pen, health device, etc.  Operating temperatures from -40℃ to +80℃; storage temperatures range from -40℃ to +85℃.

 

DRAWING

Micro OLED Display, 0.49 OELD, 64x32 OLED Micro Display, Micro OLED Screen - WEO006432A

SPECIFICATIONS

 

Interface Pin Function

No.SymbolFunction
1 C2N Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2 C2P
3 C1P
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6 NC No connection.
7 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10 SCL Host Data Input/Output Bus
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.
11 SDA
12 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
13 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
14 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 64 × 32 Dots
Module dimension 14.5 × 11.6 × 1.26 mm
Active Area 11.18 × 5.58 mm
Pixel Size 0.153 × 0.153 mm
Pixel Pitch 0.175 × 0.175 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/32 Duty
IC SSD1306

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage for Logic VDD 0 4 V
Supply Voltage for Display VCC 0 15 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +80 °C

 

Electronical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic  VDD 2.8 3 3.3 V
Supply Voltage for Display  VCC 7 7.5 7.8 V
Input High Volt. VIH 0.8×VDD VDDIO V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.9×VDD VDDIO V
Output Low Volt. VOL 0 0.1×VDD V
50% Check Board operating Current ICC VCC=7.5V 5 20 mA


SKU: WEO006432AWPP3N00000
Brand: Winstar
Available: No
Price Breaks
Quantity
1+
5+
10+
25+
Price
€3.30
€2.40
€2.30
€2.30

For quantities above 25 pcs pls send your enquiry to sales@first-components.com or call +39 0332 1888005

€3.30 excl tax

DESCRIPTION

0.49 inch passive matrix micro OLED display module which is made of 64x32 dots. It has module dimension of 14.5x 11.6 x 1.26 mm and Active Area size 11.18 × 5.58 mm. OLED micro display is built in with SSD1306 IC, it supports I2C interface, 3V power supply. COG structure OLED display which is ultra thin and no need of backlight (self emitting); it's lightweight and low power consumption. This 0.49 inch small sized OLED module is suitable for wearable device, mp3, portable device, personal care appliance, voice recorder pen, health device, etc.  Operating temperatures from -40℃ to +80℃; storage temperatures range from -40℃ to +85℃.

 

DRAWING

Micro OLED Display, 0.49 OELD, 64x32 OLED Micro Display, Micro OLED Screen - WEO006432A

SPECIFICATIONS

 

Interface Pin Function

No.SymbolFunction
1 C2N Positive Terminal of the Flying Inverting Capacitor Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2 C2P
3 C1P
4 C1N
5 VBAT Power Supply for DC/DC Converter Circuit
This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6 NC No connection.
7 VSS Ground of Logic Circuit
This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8 VDD Power Supply for Logic
This is a voltage supply pin. It must be connected to external source.
9 RES# Power Reset for Controller and Driver
This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10 SCL Host Data Input/Output Bus
When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. When I2C mode is selected, D2 & D1 should be tired together and serve as SDAout & SDAin in application and D0 is the serial clock input SCL.
11 SDA
12 IREF Current Reference for Brightness Adjustment
This pin is segment current reference pin. A resistor should be connected between this pin and VSS. Set the current lower than 12.5μA.
13 VCOMH Voltage Output High Level for COM Signal
This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
14 VCC Power Supply for OEL Panel
This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 64 × 32 Dots
Module dimension 14.5 × 11.6 × 1.26 mm
Active Area 11.18 × 5.58 mm
Pixel Size 0.153 × 0.153 mm
Pixel Pitch 0.175 × 0.175 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/32 Duty
IC SSD1306

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage for Logic VDD 0 4 V
Supply Voltage for Display VCC 0 15 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +80 °C

 

Electronical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic  VDD 2.8 3 3.3 V
Supply Voltage for Display  VCC 7 7.5 7.8 V
Input High Volt. VIH 0.8×VDD VDDIO V
Input Low Volt. VIL 0 0.2×VDD V
Output High Volt. VOH 0.9×VDD VDDIO V
Output Low Volt. VOL 0 0.1×VDD V
50% Check Board operating Current ICC VCC=7.5V 5 20 mA


Products specifications
Brand Winstar
Size 0.49"
Resolution 64x32
Active Area (mm) 11.18x5.58
Dot Size 0.15x0.15
Polarizer Glare
Color White
Power supply 3V
Display Interface I2C
Display IC SSD1306BZ
Constructive Structure COG
Frame No
Touch Panel No touch
O. Temperature (°C) -40~80
Display Connection FPC per Soldering
Pin Nr. 14
Pin Pitch 0.7mm
Preferred - Not Preferred Not Preferred
Download
Products specifications
Brand Winstar
Size 0.49"
Resolution 64x32
Active Area (mm) 11.18x5.58
Dot Size 0.15x0.15
Polarizer Glare
Color White
Power supply 3V
Display Interface I2C
Display IC SSD1306BZ
Constructive Structure COG
Frame No
Touch Panel No touch
O. Temperature (°C) -40~80
Display Connection FPC per Soldering
Pin Nr. 14
Pin Pitch 0.7mm
Preferred - Not Preferred Not Preferred
;