Cerca
Filters
Close

WEO160128W#A00-FC

PMOLED 1.92'' 160x128, White color, COG, 3V, Interface 6800,8080,SPI,I2C

DESCRIPTION

 

160x128 resolution COG graphic OLED display module, diagonal size 1.92 inch. This model is built-in with SH1108 IC; it supports 6800/8080 parallel, I2C, and 4-wire SPI serial interface. The supply voltage for logic is 3V, supply voltage for display is 12V, display with 50% check board current is 23mA @ 12Vcc (typical value), driving duty 1/128.

This 1.92 inch COG Graphic OLED module is suitable for medical applications, smart home applications, smart buildings’ devices (both homes and offices) and as well as control panels used to manage the lighting or heating, etc. Operating temperatures from -40℃ to +80℃; storage temperatures range from -40℃ to +85℃.

 

DRAWING

160x128 OLED, OLED 160x128, 1.92 OLED, 160128 OLED - WEO160128A



SPECIFICATIONS

 

Interface Pin Function

No.SymbolFunction
1 NC No connection
2 VPP This is the most positive voltage supply pad of the chip.
It should be supplied externally.
3 VSEGM This is a pad for the voltage output level for segment pre-charge.
A capacitor should be connected between this pad and VSS.
4 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
5 VSL This is a segment voltage reference pad.
A capacitor should be connected between this pad and VSS.
6 NC No connection
7 IREF This is a segment current reference pad.
A resistor should be connected between this pad and VSS. Set the current at 15.625uA.
8 VPP This is the most positive voltage supply pad of the chip.
It should be supplied externally.
9 NC No connection
10 VSS Ground for analog, logic & buffer respectively.
11 VCL This is a common voltage reference pad.
This pad should be connected to VSS externally.
12 VDD 1.65 - 3.5V power supply input pad for logic.
13 IM0 These are the MPU interface mode select pads.
 8080I2C68004-Wire SPI3-Wire SPI
IM0 0 0 0 0 1
IM1 1 1 0 0 0
IM2 1 0 1 0 0
14 IM1
16 IM2
15 VDD 1.65 - 3.5Vpower supply input pad
17 CS This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data command I/O is enabled.
18 RES This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
19 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
20 WR This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When WR = “H”: Read. When WR = “L”: Write.
21 RD This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”. When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
22 D0 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA). At this time, D2 to D7 are set to high impedance.
23 D1
24 D2
25 D3
26 D4
27 D5
28 D6
29 D7
30 NC No connection
31 VPP This is the most positive voltage supply pad of the chip.
It should be supplied externally.

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 128 × 160 Dots
Module dimension 34.5 × 48.8 × 1.41 mm
Active Area 28.908 × 39.34 mm
Pixel Size 0.206 × 0.226 mm
Pixel Pitch 0.226 × 0.246 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/128 Duty
IC SH1108
Interface 6800, 8080, SPI, I2C
Size 1.92 inch

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage for Logic VDD -0.3 3.6 V
Supply Voltage for Display VPP -0.3 17.0 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C

 

Electronical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD 1.65 3.0 3.5 V
Supply Voltage for Display VPP 11.5 12.0 12.5 V
Input High Volt. VIH 0.8xVDD VDD V
Input Low Volt. VIL VSS 0.2xVDD V
Output High Volt. VOH IOH=-0.5mA 0.8xVDD VDD V
Output Low Volt. VOL IOL=0.5mA VSS 0.2xVDD V
50% Check Board Operating Current for VPP IPP VPP=12V 23.0 35.0 mA


SKU: WEO160128W#A00-FC
Brand: Winstar
Disponibile: No
Prezzi per quantità
Quantità
1+
5+
10+
25+
Prezzo
€15,40
€11,30
€11,10
€10,70

Per quantita’ maggiori di 25pz prego invii la richiesta a sales@first-components.com o chiami il +39 0332 1888005

€15,40 IVA esclusa

DESCRIPTION

 

160x128 resolution COG graphic OLED display module, diagonal size 1.92 inch. This model is built-in with SH1108 IC; it supports 6800/8080 parallel, I2C, and 4-wire SPI serial interface. The supply voltage for logic is 3V, supply voltage for display is 12V, display with 50% check board current is 23mA @ 12Vcc (typical value), driving duty 1/128.

This 1.92 inch COG Graphic OLED module is suitable for medical applications, smart home applications, smart buildings’ devices (both homes and offices) and as well as control panels used to manage the lighting or heating, etc. Operating temperatures from -40℃ to +80℃; storage temperatures range from -40℃ to +85℃.

 

DRAWING

160x128 OLED, OLED 160x128, 1.92 OLED, 160128 OLED - WEO160128A



SPECIFICATIONS

 

Interface Pin Function

No.SymbolFunction
1 NC No connection
2 VPP This is the most positive voltage supply pad of the chip.
It should be supplied externally.
3 VSEGM This is a pad for the voltage output level for segment pre-charge.
A capacitor should be connected between this pad and VSS.
4 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
5 VSL This is a segment voltage reference pad.
A capacitor should be connected between this pad and VSS.
6 NC No connection
7 IREF This is a segment current reference pad.
A resistor should be connected between this pad and VSS. Set the current at 15.625uA.
8 VPP This is the most positive voltage supply pad of the chip.
It should be supplied externally.
9 NC No connection
10 VSS Ground for analog, logic & buffer respectively.
11 VCL This is a common voltage reference pad.
This pad should be connected to VSS externally.
12 VDD 1.65 - 3.5V power supply input pad for logic.
13 IM0 These are the MPU interface mode select pads.
 8080I2C68004-Wire SPI3-Wire SPI
IM0 0 0 0 0 1
IM1 1 1 0 0 0
IM2 1 0 1 0 0
14 IM1
16 IM2
15 VDD 1.65 - 3.5Vpower supply input pad
17 CS This pad is the chip select input. When CS = “L”, then the chip select becomes active, and data command I/O is enabled.
18 RES This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
19 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
20 WR This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal. When connected to a 6800 Series MPU: This is the read/write control signal input terminal. When WR = “H”: Read. When WR = “L”: Write.
21 RD This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”. When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
22 D0 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDA). At this time, D2 to D7 are set to high impedance.
23 D1
24 D2
25 D3
26 D4
27 D5
28 D6
29 D7
30 NC No connection
31 VPP This is the most positive voltage supply pad of the chip.
It should be supplied externally.

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 128 × 160 Dots
Module dimension 34.5 × 48.8 × 1.41 mm
Active Area 28.908 × 39.34 mm
Pixel Size 0.206 × 0.226 mm
Pixel Pitch 0.226 × 0.246 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/128 Duty
IC SH1108
Interface 6800, 8080, SPI, I2C
Size 1.92 inch

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage for Logic VDD -0.3 3.6 V
Supply Voltage for Display VPP -0.3 17.0 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C

 

Electronical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD 1.65 3.0 3.5 V
Supply Voltage for Display VPP 11.5 12.0 12.5 V
Input High Volt. VIH 0.8xVDD VDD V
Input Low Volt. VIL VSS 0.2xVDD V
Output High Volt. VOH IOH=-0.5mA 0.8xVDD VDD V
Output Low Volt. VOL IOL=0.5mA VSS 0.2xVDD V
50% Check Board Operating Current for VPP IPP VPP=12V 23.0 35.0 mA


Specifiche di prodotto
Brand Winstar
Size 1.92"
Risoluzione 160x128
Area Attiva (mm) 28.91x39.34
Dot Size 0.21x0.22
Polarizzatore Glare
Colore White
Alimentazione 3V
Interfaccia Display 6800/8080/SPI/I2C
IC Controller Display SH1108
Struttura COG
Frame No
Touch Panel No touch
Connessione Display FPC per ZIF Connector
Nr. Pin 31
Passo Pin 0.5mm
Preferred - Not Preferred Preferred
Download
Specifiche di prodotto
Brand Winstar
Size 1.92"
Risoluzione 160x128
Area Attiva (mm) 28.91x39.34
Dot Size 0.21x0.22
Polarizzatore Glare
Colore White
Alimentazione 3V
Interfaccia Display 6800/8080/SPI/I2C
IC Controller Display SH1108
Struttura COG
Frame No
Touch Panel No touch
Connessione Display FPC per ZIF Connector
Nr. Pin 31
Passo Pin 0.5mm
Preferred - Not Preferred Preferred
Ultimi prodotti visti
;