Cerca
Filters
Close

WEO1602L#HPP3N00000-FC

PMOLED 1.23'' 16x2, Yellow color, COG, 3.3V, Interface 6800/8080/SPI/I2C, Glare

DESCRIPTION

16 Character x 2 lines COG OLED display module. This 16x2 OLED display is built-in with WS0012 IC; it supports 6800/8080 8-bit parallel and I2C, 4-wire SPI interface, the supply voltage for logic is 3.3V (VDD), and the supply voltage for display is 8.5V(VCC). The current with 50% checkerboard display is 2mA @ VCC 8.5V (for white color), 1/16 driving duty. Operating temperatures from -40℃ to +80℃; storage temperatures from -40℃ to +85℃.

We suggest customers consider using this low-power 16x2 character OLED to upgrade the existing STN character display. Below are the advantages of this OLED display.

►Faster response time "At +25 ℃ 10 μsec
►Unlimited viewing angle "Up to 175 degree
►Thin – No need of backlight, self-emitting
►High Brightness
►High contrast ratio 10,000:1
►Wide Operation Temperature
►Lower power consumption

DRAWING

SPECIFICATIONS

Interface Pin Function

 
Pin No.SymbolLevelDescription
1 GND P Ground Pin
2 V16 I This is the most positive voltage supply pin of the chip. It can be supplied externally or generated internally by using internal DC-DC voltage converter.
3 VCI P DCDC buffer Power Supply
4 GND P Ground Pin
5 VCC P Power Pin
6 BVR I Brightness control pin. It should be connected to VCC.
7 DVR I Pre charge time control. It should be connected to VCC.
8 VBREF O This pin is the internal voltage reference of DCDC1 circuit. A stabilization capacitor should be connected between this pin and GND
9 RESE I NMOS source input pin:
This pin connects to the source current pin of the external NMOS of the booster circuit.
10 GDR O Gate drive pulse output pin:
This output pin drives the gate of external NMOS of the booster circuit.
11 FB I Feedback voltage input pin:
This pin is the feedback resistor input of the booster circuit. It is used to adjust the booster output voltage level.
12 VDD P Power Pin (connect to stabilization capacitor)
13 IM1 I Interface selection
IM1IM0Interface
L L 6800-series
L H 8080-series
H L SPI
H H I2C
14 IM0 I
15 RESETB I Reset pin
16 RS I Register Select Input Pin
When this pin is set to "0", it is used as an Instruction Register.
When this pin is set to "1", it is used for as the Data Register.
17 CSB I Chip select input pins
Data / instruction I/O is enabled only when CSB is “L”.
18 RDB I Read / Write execution control pin
MPU TypeRDBDescription
6800-series E Read / Write control input pin
- RW = “H”: When E is “H”, DB0 to DB7 are in an output status.
- RW = “L”: The data on DB0 to DB7 are latched at the falling edge the E signal.
8080-series RDB Read enable clock input pin
When / RDB is “L”, DB0 to DB7 are in an output status.
19 WRB I Read / Write execution control pin
MPU TypeWRBDescription
6800-series RW Read / Write control input pin
- RW = “H” : read
- RW = “L” : write
8080-series WRB Write enable clock input pin.
The data on DB0 to DB7 are latched at the rising edge of the /WRB signal.
20 SDA I/O SDA is the serial data input for I2C.
21 SDC I/O SDC is the serial clock input/output for I2C.
22~25 DB7~DB4 I/O High Order Bidirectional Data I/O Pins
These pins are used for data transfer and reception between the MPU and WS0012.
When SPI is selected, DB5 will be the serial clock input: SCL
DB7 will be the serial data input: SDI.
DB6 will be the serial data output: SDO.
26~29 DB3~DB0 I/O Low Order Bidirectional Data I/O Pins
These pins are used for data transfer and reception between the MPU and WS0012.
These pins are not used during a 4-bit operation.
30 GND P Ground Pin

 

Mechanical Data

ItemDimensionUnit
Number of Characters 16 characters x 2 Lines
Module dimension 39.1 x 15.8 x 2.01 mm
View area 32.69 x 7.94 mm
Active area 30.69 x 5.94 mm
Dot size 0.297 x 0.315 mm
Dot pitch 0.342 x 0.36 mm
Character size 1.66 x 2.835 mm
Character pitch 1.935 x 3.105 mm
Panel type OLED , Monochrome
Duty 1/16
IC WS0012
Interface 6800, 8080, SPI, I2C
Size 1.23 inch

 

Absolute Maximum Ratings

ItemSymbolMinMaxUnit
Operating Temperature TOP -40 +80 °C
Storage Temperature TST -40 +85 °C
Supply Voltage For Logic VCC -0.3 3.6 V
Supply Voltage For DCDC converter VCI -0.3 3.6 V
Supply Voltage for Display V16 -0.3 19.0 V

 

Electronical Characteristics

DC Electrical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage For Logic VCC 2.6 3.3 3.5 V
Supply Voltage For DCDC converter VCI 2.6 3.3 3.5 V
Supply Voltage for Display V16 12.5 13.0 V
Input High Volt. VIH 0.9xVCC VCC V
Input Low Volt. VIL GND 0.1xVCC V
Output High Volt. VOH IOH=-0.5mA 0.8xVCC VCC V
Output Low Volt. VOL IOL=0.5mA GND 0.2xVCC V
50% Checkerboard
Operating Current
I16 V16=12.5V 2 4 mA

 

SKU: WEO1602L#HPP3N00000-FC
Brand: Winstar
Disponibile: No
Prezzi per quantità
Quantità
1+
5+
10+
25+
Prezzo
€8,40
€6,10
€5,90
€5,70

Per quantita’ maggiori di 25pz prego invii la richiesta a sales@first-components.com o chiami il +39 0332 1888005

€8,40 IVA esclusa

DESCRIPTION

16 Character x 2 lines COG OLED display module. This 16x2 OLED display is built-in with WS0012 IC; it supports 6800/8080 8-bit parallel and I2C, 4-wire SPI interface, the supply voltage for logic is 3.3V (VDD), and the supply voltage for display is 8.5V(VCC). The current with 50% checkerboard display is 2mA @ VCC 8.5V (for white color), 1/16 driving duty. Operating temperatures from -40℃ to +80℃; storage temperatures from -40℃ to +85℃.

We suggest customers consider using this low-power 16x2 character OLED to upgrade the existing STN character display. Below are the advantages of this OLED display.

►Faster response time "At +25 ℃ 10 μsec
►Unlimited viewing angle "Up to 175 degree
►Thin – No need of backlight, self-emitting
►High Brightness
►High contrast ratio 10,000:1
►Wide Operation Temperature
►Lower power consumption

DRAWING

SPECIFICATIONS

Interface Pin Function

 
Pin No.SymbolLevelDescription
1 GND P Ground Pin
2 V16 I This is the most positive voltage supply pin of the chip. It can be supplied externally or generated internally by using internal DC-DC voltage converter.
3 VCI P DCDC buffer Power Supply
4 GND P Ground Pin
5 VCC P Power Pin
6 BVR I Brightness control pin. It should be connected to VCC.
7 DVR I Pre charge time control. It should be connected to VCC.
8 VBREF O This pin is the internal voltage reference of DCDC1 circuit. A stabilization capacitor should be connected between this pin and GND
9 RESE I NMOS source input pin:
This pin connects to the source current pin of the external NMOS of the booster circuit.
10 GDR O Gate drive pulse output pin:
This output pin drives the gate of external NMOS of the booster circuit.
11 FB I Feedback voltage input pin:
This pin is the feedback resistor input of the booster circuit. It is used to adjust the booster output voltage level.
12 VDD P Power Pin (connect to stabilization capacitor)
13 IM1 I Interface selection
IM1IM0Interface
L L 6800-series
L H 8080-series
H L SPI
H H I2C
14 IM0 I
15 RESETB I Reset pin
16 RS I Register Select Input Pin
When this pin is set to "0", it is used as an Instruction Register.
When this pin is set to "1", it is used for as the Data Register.
17 CSB I Chip select input pins
Data / instruction I/O is enabled only when CSB is “L”.
18 RDB I Read / Write execution control pin
MPU TypeRDBDescription
6800-series E Read / Write control input pin
- RW = “H”: When E is “H”, DB0 to DB7 are in an output status.
- RW = “L”: The data on DB0 to DB7 are latched at the falling edge the E signal.
8080-series RDB Read enable clock input pin
When / RDB is “L”, DB0 to DB7 are in an output status.
19 WRB I Read / Write execution control pin
MPU TypeWRBDescription
6800-series RW Read / Write control input pin
- RW = “H” : read
- RW = “L” : write
8080-series WRB Write enable clock input pin.
The data on DB0 to DB7 are latched at the rising edge of the /WRB signal.
20 SDA I/O SDA is the serial data input for I2C.
21 SDC I/O SDC is the serial clock input/output for I2C.
22~25 DB7~DB4 I/O High Order Bidirectional Data I/O Pins
These pins are used for data transfer and reception between the MPU and WS0012.
When SPI is selected, DB5 will be the serial clock input: SCL
DB7 will be the serial data input: SDI.
DB6 will be the serial data output: SDO.
26~29 DB3~DB0 I/O Low Order Bidirectional Data I/O Pins
These pins are used for data transfer and reception between the MPU and WS0012.
These pins are not used during a 4-bit operation.
30 GND P Ground Pin

 

Mechanical Data

ItemDimensionUnit
Number of Characters 16 characters x 2 Lines
Module dimension 39.1 x 15.8 x 2.01 mm
View area 32.69 x 7.94 mm
Active area 30.69 x 5.94 mm
Dot size 0.297 x 0.315 mm
Dot pitch 0.342 x 0.36 mm
Character size 1.66 x 2.835 mm
Character pitch 1.935 x 3.105 mm
Panel type OLED , Monochrome
Duty 1/16
IC WS0012
Interface 6800, 8080, SPI, I2C
Size 1.23 inch

 

Absolute Maximum Ratings

ItemSymbolMinMaxUnit
Operating Temperature TOP -40 +80 °C
Storage Temperature TST -40 +85 °C
Supply Voltage For Logic VCC -0.3 3.6 V
Supply Voltage For DCDC converter VCI -0.3 3.6 V
Supply Voltage for Display V16 -0.3 19.0 V

 

Electronical Characteristics

DC Electrical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage For Logic VCC 2.6 3.3 3.5 V
Supply Voltage For DCDC converter VCI 2.6 3.3 3.5 V
Supply Voltage for Display V16 12.5 13.0 V
Input High Volt. VIH 0.9xVCC VCC V
Input Low Volt. VIL GND 0.1xVCC V
Output High Volt. VOH IOH=-0.5mA 0.8xVCC VCC V
Output Low Volt. VOL IOL=0.5mA GND 0.2xVCC V
50% Checkerboard
Operating Current
I16 V16=12.5V 2 4 mA

 

Specifiche di prodotto
Brand Winstar
Size 1.23"
Risoluzione 16x2
Area Attiva (mm) 30.69x5.94
Dot Size 0.29x0.31
Polarizzatore Glare
Colore Yellow
Alimentazione 3.3V
Interfaccia Display 6800/8080/SPI/I2C
Display IC WS0012
Struttura Costruttiva COG
Frame No
Touch Panel No touch
Temperatura O. (°C) -40~80
Connessione Display FFC per ZIF Connector
Nr. Pin 30
Passo Pin 0.5mm
Preferred - Not Preferred Preferred
Download
Specifiche di prodotto
Brand Winstar
Size 1.23"
Risoluzione 16x2
Area Attiva (mm) 30.69x5.94
Dot Size 0.29x0.31
Polarizzatore Glare
Colore Yellow
Alimentazione 3.3V
Interfaccia Display 6800/8080/SPI/I2C
Display IC WS0012
Struttura Costruttiva COG
Frame No
Touch Panel No touch
Temperatura O. (°C) -40~80
Connessione Display FFC per ZIF Connector
Nr. Pin 30
Passo Pin 0.5mm
Preferred - Not Preferred Preferred
;