DESCRIPTION
Industrial grade 5.5-inch COF Graphic OLED with frame bezel and Capacitive Touchscreen, made of resolution 256x64 dots. This OLED module is built-in with SSD1322 COF IC; it supports 6800/8080 8-bit parallel, and 3-wire/4-wire SPI interface, supports 16 (4-bit) gray scale, supply voltage for logic 3V, the display current with 50% checkerboard is 240mA @3.0V VDD (typical value), 1/64 driving duty. This model is having Capacitive Touchscreen on module; it is built-in with GT911 IC which supports I2C interface, one detect point for CTP, normal glare surface glass. The module is having PCB on module which is suitable for customers to use wire connection; customers do not need to develop extra PCB for their applications. Also, we integrated VCC circuit on PCB to make it easier for customers to use. This module is also supporting many wiring methods like PIN, FFC, CN, FPC.
There are four mounting holes on PCB board which is an easy method for customers to fix modules on their applications. This OLED module is suitable for smart home application, medical device, industrial control, etc. This model can be operating at temperatures from -20°C to +70°C; its storage temperatures range from -30°C to +80°C.
DRAWING

SPECIFICATIONS
Interface Pin Function
| Pin Number | Symbol | I/O | Function |
| 1 |
VSS |
P |
Ground. |
| 2 |
VDD |
P |
Power Supply for Core Logic Circuit Power supply pin for core logic operation. A capacitor is required to connect between this pin and VSS |
| 3 |
N.C. |
P |
Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
| 4 |
D/C# |
I |
Data/Command Control This pin is Data/Command control pin connecting to the MCU. When the pin is pulled HIGH, the content at D[7:0] will be interpreted as data. When the pin is pulled LOW, the content at D[7:0] will be interpreted as command. |
| 5 |
R/W# (WR#) |
I |
Read/Write Select or Write This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Pull this pin to “High” for read mode and pull it to “Low” for write mode. When 80XX interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled low and the CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
| 6 |
E/RD# |
I |
Read/Write Enable or Read This pin is MCU interface input. When interfacing to a 68XX-series microprocessor, this pin will be used as the Enable (E) signal. Read/write operation is initiated when this pin is pulled high and the CS# is pulled low. When connecting to an 80XX-microprocessor, this pin receives the Read (RD#) signal. Data read operation is initiated when this pin is pulled low and CS# is pulled low. When serial mode is selected, this pin must be connected to VSS. |
| 7~14 |
DB0 |
I/O |
Host Data Input/Output Bus These pins are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus. When serial mode is selected, D1 will be the serial data input SDIN and D0 will be the serial clock input SCLK. |
| DB1 |
| DB2 |
| DB3 |
| DB4 |
| DB5 |
| DB6 |
| DB7 |
| 15 |
NC |
P |
Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
| 16 |
RES# |
I |
This pin is reset signal input. When the pin is pulled LOW, initialization of the chip is executed. Keep this pin pull HIGH during normal operation. |
| 17 |
CS# |
I |
Data/Command Control This pin is the chip select input connecting to the MCU. The chip is enabled for MCU communication only when CS# is pulled LOW. |
| 18 |
NC |
P |
Reserved Pin The N.C. pin between function pins are reserved for compatible and flexible design. |
| 19 |
BS1 |
I |
Communicating Protocol Select These pins are MCU interface selection input. See the following table:
| BS[1:0] | Bus Interface Selection |
| 00 |
4 line SPI |
| 01 |
3 line SPI |
| 10 |
8-bit 8080 parallel |
| 11 |
8-bit 6800 parallel |
Note (1) 0 is connected to VSS (2) 1 is connected to VDD |
| 20 |
BS0 |
| 21 |
TP_SCK |
I |
I2C clock input |
| 22 |
TP_SDA |
I |
I2C data input and output |
| 23 |
TP_INT |
I |
External interrupt to the host |
| 24 |
TP_RST |
I |
External Reset, Low is active |
General Specification
| Item | Dimension | Unit |
| Dot Matrix |
256 × 64 Dots |
- |
| Module dimension |
147.0 × 59 × 4.8 |
mm |
| Active Area |
135.65 × 33.89 |
mm |
| Pixel Size |
0.5 × 0.5 |
mm |
| Pixel Pitch |
0.53 × 0.53 |
mm |
| Display Mode |
Passive Matrix |
| Display Color |
Monochrome |
| Drive Duty |
1/64 Duty |
| Gray Scale |
4 bits |
| OLED IC |
SSD1322 |
| OLED Interface |
6800, 8080, SPI |
| Size |
5.5 inch |
| CTP IC |
GT911 |
| Detect Point |
1 |
| CTP Interface |
I2C |
| Surface |
Normal Glare |
Absolute Maximum Ratings
| Parameter | Symbol | Min | Max | Unit |
| Supply Voltage for Display |
VDD |
-0.3 |
4 |
V |
| Operating Temperature |
TOP |
-20 |
+70 |
°C |
| Storage Temperature |
TSTG |
-30 |
+80 |
°C |
Electronical Characteristics
DC Electrical Characteristics
| Item | Symbol | Condition | Min | Typ | Max | Unit |
| Supply Voltage for Logic |
VDD |
- |
2.8 |
3.0 |
3.3 |
V |
| High Level Input |
VIH |
- |
0.8×VDD |
- |
VDD |
V |
| Low Level Input |
VIL |
- |
0 |
- |
0.2×VDD |
V |
| High Level Output |
VOH |
- |
0.9×VDD |
- |
VDD |
V |
| Low Level Output |
VOL |
- |
0 |
- |
0.1×VDD |
V |
| 50% Check Board operating Current |
IDD |
VDD =3V |
- |
240 |
400 |
mA |
Specifiche di prodotto
|
Size
|
5.5" |
|
Resolution
|
256x64 |
|
Active Area (mm)
|
135.65x33.89 |
|
Dot Size
|
0.50x0.50 |
|
Polarizer
|
Glare |
|
Color
|
Green |
|
Power supply
|
3V |
|
Display Interface
|
6800/8080/SPI |
|
Display IC
|
SSD1322 |
|
Constructive Structure
|
COF + PCB |
|
Frame
|
Yes |
|
Touch Panel
|
Capacitive |
|
O. Temperature (°C)
|
-40~80 |
|
Data Connection
|
Soldering PAD |
|
Pin Nr.
|
24 |
|
Pin Pitch
|
2.54mm |
|
Touch Panel IC Controller
|
GT911 |
|
Preferred - Not Preferred
|
Preferred |