Menu
Cerca
Filters
Close
Menu

WEO12864W#Q02D-FC

Immagine di WEO12864W#Q02D-FC Immagine di WEO12864W#Q02D-FC
PMOLED 2.7'' 128x64, White color, COG, 3V, Interface 6800,8080,SPI,I2C, Glare, Capacitive touch panel (GT911)

DESCRIPTION

 

Most popular 2.7 inch COG Graphic OLED display with Capacitive Touch Panel on module; which is made of resolution 128x64 dots. This module is built in with SSD1309 IC, it supports 6800/8080 8-bit parallel, 4-Wire SPI and I2C interface, supply voltage for logic is from 2.8V to 3.3V, typical value 3.0V, supply voltage for display 13V, 1/64 driving duty. This model adopted GT911 as touch IC, which supports I2C interface, one Detect Point for CTP.

Available colors: White, Yellow, Green, Sky blue.

This 2.7" with CTP model is ideal for smart home applications, intelligent technology devices, energy systems, meter devices, communication systems, medical instrument, etc. Operating at temperatures from -20℃ to 70℃; istorage temperatures  from -30℃ to 80℃.

 

DRAWING

2.7, 128x64 Graphic OLED Display with Capacitive Touch Panel - WEO012864Q-CTP

 

SPECIFICATIONS

Interface Pin Function

No.SymbolFunction
1 NC(GND) No connection
2 VLSS This is an analog ground pin
3 VSS Ground.
4 NC No connection
5 VDD Power supply pin for core logic operation
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
 BS1BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68XX parallel 0 1
8-bit 80XX parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
7 BS2
8 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
9 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
10 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
11 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
12 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
13-20 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
21 IREF This pin is the segment output current reference pin.
IREF is supplied externally.
22 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
23 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
24 NC(GND) No connection

 

CTP PIN Definition

No.SymbolFunction
1 GND Power ground
2 VDD Power supply
3 INT Interrupt signal, active low, asserted to request
Host start a new transaction
4 SDA I2C data signal
5 SCL I2C clock signal
6 RST External reset signal, active low
7 GND Power ground
8 GND Power ground
9 GND Power ground
10 GND Power ground

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 128 x 64 －
Module dimension 74.8 × 44.16 × 3.66 mm
Active Area 61.41 × 30.69 mm
Pixel Size 0.45 × 0.45 mm
Pixel Pitch 0.48 × 0.48 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/64 Duty
IC SSD1309
Interface 6800,8080,4-Wire SPI,I2C
Size 2.7 inch
CTP IC GT911
Detect Point 1
CTP Interface I2C
Surface Glare

 

Absolute Maximum Ratings

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage for Logic VDD -0.3 4 V
Supply Voltage for Display VCC 0 15 V
Operating Temperature TOP -20 +70 °C
Storage Temperature TSTG -30 +80 °C
 

 

Touch Panel Controller GT911

ParameterSymbolMinMaxUnit
Power Supply Voltage VDD 2.66 3.47 V

 

Electronical Characteristics

DC Electrical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD － 2.8 3.0 3.3 V
Supply Voltage for Display VCC － 12.5 13 13.5 V
High Level Input VIH － 0.8×VDD － － V
Low Level Input VIL － － － 0.2×VDD V
High Level Output VOH － 0.9×VDD － － V
Low Level Output VOL － － － 0.1×VDD V
50% Check Board operating Current VCC =13.0V 20 30 50 mA
 

 

Touch Panel Controller GT911

ItemSymbolMinTypMaxUnit
Supply Voltage VDD 2.8 3.0 3.3 V
Input High Volt. VIH 0.75xVDD   VDD+0.3 V
Input Low Volt. VIL -0.3 － 0.25xVDD V
Output High Volt. VOH 0.85xVDD － － V
Output Low Volt. VOL － － 0.15xVDD V


SKU: WEO12864W#Q02D-FC
Brand: Winstar
Disponibile: Si
Si tratta dela prima recensione per questo prodotto
Kit Accessori
Prezzi per quantità
Quantità
1+
5+
10+
Prezzo
€38,50
€32,10
€31,40

Per quantita’ maggiori di 25pz prego invii la richiesta a sales@first-components.com o chiami il +39 0332 1888005

€38,50 IVA esclusa

DESCRIPTION

 

Most popular 2.7 inch COG Graphic OLED display with Capacitive Touch Panel on module; which is made of resolution 128x64 dots. This module is built in with SSD1309 IC, it supports 6800/8080 8-bit parallel, 4-Wire SPI and I2C interface, supply voltage for logic is from 2.8V to 3.3V, typical value 3.0V, supply voltage for display 13V, 1/64 driving duty. This model adopted GT911 as touch IC, which supports I2C interface, one Detect Point for CTP.

Available colors: White, Yellow, Green, Sky blue.

This 2.7" with CTP model is ideal for smart home applications, intelligent technology devices, energy systems, meter devices, communication systems, medical instrument, etc. Operating at temperatures from -20℃ to 70℃; istorage temperatures  from -30℃ to 80℃.

 

DRAWING

2.7, 128x64 Graphic OLED Display with Capacitive Touch Panel - WEO012864Q-CTP

 

SPECIFICATIONS

Interface Pin Function

No.SymbolFunction
1 NC(GND) No connection
2 VLSS This is an analog ground pin
3 VSS Ground.
4 NC No connection
5 VDD Power supply pin for core logic operation
6 BS1 MCU bus interface selection pins. Select appropriate logic setting as described in the following table. BS2 and BS1 are pin select
 BS1BS2
I2C 1 0
4-wire Serial 0 0
8-bit 68XX parallel 0 1
8-bit 80XX parallel 1 1
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD
7 BS2
8 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
9 RES# This pin is reset signal input.
When the pin is pulled LOW, initialization of the chip is executed.
Keep this pin pull HIGH during normal operation.
10 D/C# This pin is Data/Command control pin connecting to the MCU.
When the pin is pulled HIGH, the data at D[7:0] will be interpreted as data.
When the pin is pulled LOW, the data at D[7:0] will be transferred to a command register.
In I2C mode, this pin acts as SA0 for slave address selection.
11 R/W# This pin is read / write control input pin connecting to the MCU interface.
When 6800 interface mode is selected, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
12 E/RD# This pin is MCU interface input.
When 6800 interface mode is selected, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH and the chip is selected.
When 8080 interface mode is selected, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
13-20 D0~D7 These pins are bi-directional data bus connecting to the MCU data bus.
Unused pins are recommended to tie LOW.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN and D2 should be kept NC.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
21 IREF This pin is the segment output current reference pin.
IREF is supplied externally.
22 VCOMH COM signal deselected voltage level.
A capacitor should be connected between this pin and VSS.
23 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
24 NC(GND) No connection

 

CTP PIN Definition

No.SymbolFunction
1 GND Power ground
2 VDD Power supply
3 INT Interrupt signal, active low, asserted to request
Host start a new transaction
4 SDA I2C data signal
5 SCL I2C clock signal
6 RST External reset signal, active low
7 GND Power ground
8 GND Power ground
9 GND Power ground
10 GND Power ground

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 128 x 64 －
Module dimension 74.8 × 44.16 × 3.66 mm
Active Area 61.41 × 30.69 mm
Pixel Size 0.45 × 0.45 mm
Pixel Pitch 0.48 × 0.48 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/64 Duty
IC SSD1309
Interface 6800,8080,4-Wire SPI,I2C
Size 2.7 inch
CTP IC GT911
Detect Point 1
CTP Interface I2C
Surface Glare

 

Absolute Maximum Ratings

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage for Logic VDD -0.3 4 V
Supply Voltage for Display VCC 0 15 V
Operating Temperature TOP -20 +70 °C
Storage Temperature TSTG -30 +80 °C
 

 

Touch Panel Controller GT911

ParameterSymbolMinMaxUnit
Power Supply Voltage VDD 2.66 3.47 V

 

Electronical Characteristics

DC Electrical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD － 2.8 3.0 3.3 V
Supply Voltage for Display VCC － 12.5 13 13.5 V
High Level Input VIH － 0.8×VDD － － V
Low Level Input VIL － － － 0.2×VDD V
High Level Output VOH － 0.9×VDD － － V
Low Level Output VOL － － － 0.1×VDD V
50% Check Board operating Current VCC =13.0V 20 30 50 mA
 

 

Touch Panel Controller GT911

ItemSymbolMinTypMaxUnit
Supply Voltage VDD 2.8 3.0 3.3 V
Input High Volt. VIH 0.75xVDD   VDD+0.3 V
Input Low Volt. VIL -0.3 － 0.25xVDD V
Output High Volt. VOH 0.85xVDD － － V
Output Low Volt. VOL － － 0.15xVDD V


Specifiche di prodotto
Brand Winstar
Size 2.7"
Risoluzione 128x64
Area Attiva (mm) 61.41x30.69
Dot Size 0.45x0.45
Polarizzatore Glare
Colore White
Alimentazione 3V
Interfaccia 6800/8080/SPI/I2C
Controllore a Bordo SSD1309ZC
Struttura COG
Frame No
Touch Panel Capacitive
Connessione Display FPC per ZIF Connector
Nr. Pin 24
Passo Pin 0.5mm
Preferred - Not Preferred Preferred
Download
Specifiche di prodotto
Brand Winstar
Size 2.7"
Risoluzione 128x64
Area Attiva (mm) 61.41x30.69
Dot Size 0.45x0.45
Polarizzatore Glare
Colore White
Alimentazione 3V
Interfaccia 6800/8080/SPI/I2C
Controllore a Bordo SSD1309ZC
Struttura COG
Frame No
Touch Panel Capacitive
Connessione Display FPC per ZIF Connector
Nr. Pin 24
Passo Pin 0.5mm
Preferred - Not Preferred Preferred
Prodotti correlati
Immagine di MOLEX_52437-2433

MOLEX_52437-2433

ZIF Connector 24 pins, 0.5mm pitch, Bottom contact
Da €4,50 IVA esclusa
Immagine di WEO12864L#Q02D-FC

WEO12864L#Q02D-FC

PMOLED 2.7'' 128x64, Yellow color, COG, 3V, Interface 6800,8080,SPI,I2C, Glare, Capacitive touch panel (GT911)
Da €31,10 IVA esclusa
Categorie
Ultimi prodotti visti
Contatti
  • +39 0332 1888005
  • +39 0332 320856
  • Via Cavour, 69 21020 Buguggiate (VA) Italy
  • Partita IVA IT02764420127
    REA di Varese 285686
    Cap.sociale interamente versato 100.000€
Informazioni
Nuovi prodotti
Copyright © 2020 FIRST Components. Tutti i diritti riservati
Powered by nopCommerce
Developed by Weblink
FIRST Components s.r.l.
Via Cavour, 69 21020 Buguggiate (VA) Italy
;