Cerca
Italiano
Catalogo
    Menu Chiudi

    WEO1602W#HP3N00000-FC

    PMOLED 1.23" 16x2, White color, COG, 3.3V, Interface 6800/8080/SPI/I2C, Glare
    Brand: Winstar
    Cod.: WEO1602W#HP3N00000-FC
    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    25+
    Prezzo
    €10,30
    €9,30
    €8,70
    €8,50

    Per quantità maggiori di 49pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Disponibile
    €10,30 IVA esclusa
    i h

    DESCRIPTION

    16 Character x 2 lines COG OLED display module. This 16x2 OLED display is built-in with WS0012 IC; it supports 6800/8080 8-bit parallel and I2C, 4-wire SPI interface, the supply voltage for logic is 3.3V (VDD), and the supply voltage for display is 8.5V(VCC). The current with 50% checkerboard display is 2mA @ VCC 8.5V (for white color), 1/16 driving duty. Operating temperatures from -40℃ to +80℃; storage temperatures from -40℃ to +85℃.

    We suggest customers consider using this low-power 16x2 character OLED to upgrade the existing STN character display. Below are the advantages of this OLED display.

    ►Faster response time "At +25 ℃ 10 μsec
    ►Unlimited viewing angle "Up to 175 degree
    ►Thin – No need of backlight, self-emitting
    ►High Brightness
    ►High contrast ratio 10,000:1
    ►Wide Operation Temperature
    ►Lower power consumption

    DRAWING

    SPECIFICATIONS

    Interface Pin Function

     
    Pin No.SymbolLevelDescription
    1 GND P Ground Pin
    2 V16 I This is the most positive voltage supply pin of the chip. It can be supplied externally or generated internally by using internal DC-DC voltage converter.
    3 VCI P DCDC buffer Power Supply
    4 GND P Ground Pin
    5 VCC P Power Pin
    6 BVR I Brightness control pin. It should be connected to VCC.
    7 DVR I Pre charge time control. It should be connected to VCC.
    8 VBREF O This pin is the internal voltage reference of DCDC1 circuit. A stabilization capacitor should be connected between this pin and GND
    9 RESE I NMOS source input pin:
    This pin connects to the source current pin of the external NMOS of the booster circuit.
    10 GDR O Gate drive pulse output pin:
    This output pin drives the gate of external NMOS of the booster circuit.
    11 FB I Feedback voltage input pin:
    This pin is the feedback resistor input of the booster circuit. It is used to adjust the booster output voltage level.
    12 VDD P Power Pin (connect to stabilization capacitor)
    13 IM1 I Interface selection
    IM1IM0Interface
    L L 6800-series
    L H 8080-series
    H L SPI
    H H I2C
    14 IM0 I
    15 RESETB I Reset pin
    16 RS I Register Select Input Pin
    When this pin is set to "0", it is used as an Instruction Register.
    When this pin is set to "1", it is used for as the Data Register.
    17 CSB I Chip select input pins
    Data / instruction I/O is enabled only when CSB is “L”.
    18 RDB I Read / Write execution control pin
    MPU TypeRDBDescription
    6800-series E Read / Write control input pin
    - RW = “H”: When E is “H”, DB0 to DB7 are in an output status.
    - RW = “L”: The data on DB0 to DB7 are latched at the falling edge the E signal.
    8080-series RDB Read enable clock input pin
    When / RDB is “L”, DB0 to DB7 are in an output status.
    19 WRB I Read / Write execution control pin
    MPU TypeWRBDescription
    6800-series RW Read / Write control input pin
    - RW = “H” : read
    - RW = “L” : write
    8080-series WRB Write enable clock input pin.
    The data on DB0 to DB7 are latched at the rising edge of the /WRB signal.
    20 SDA I/O SDA is the serial data input for I2C.
    21 SDC I/O SDC is the serial clock input/output for I2C.
    22~25 DB7~DB4 I/O High Order Bidirectional Data I/O Pins
    These pins are used for data transfer and reception between the MPU and WS0012.
    When SPI is selected, DB5 will be the serial clock input: SCL
    DB7 will be the serial data input: SDI.
    DB6 will be the serial data output: SDO.
    26~29 DB3~DB0 I/O Low Order Bidirectional Data I/O Pins
    These pins are used for data transfer and reception between the MPU and WS0012.
    These pins are not used during a 4-bit operation.
    30 GND P Ground Pin

     

    Mechanical Data

    ItemDimensionUnit
    Number of Characters 16 characters x 2 Lines -
    Module dimension 39.1 x 15.8 x 2.01 mm
    View area 32.69 x 7.94 mm
    Active area 30.69 x 5.94 mm
    Dot size 0.297 x 0.315 mm
    Dot pitch 0.342 x 0.36 mm
    Character size 1.66 x 2.835 mm
    Character pitch 1.935 x 3.105 mm
    Panel type OLED , Monochrome
    Duty 1/16
    IC WS0012
    Interface 6800, 8080, SPI, I2C
    Size 1.23 inch

     

    Absolute Maximum Ratings

    ItemSymbolMinMaxUnit
    Operating Temperature TOP -40 +80 °C
    Storage Temperature TST -40 +85 °C
    Supply Voltage For Logic VCC -0.3 3.6 V
    Supply Voltage For DCDC converter VCI -0.3 3.6 V
    Supply Voltage for Display V16 -0.3 19.0 V

     

    Electronical Characteristics

    DC Electrical Characteristics

    ItemSymbolConditionMinTypMaxUnit
    Supply Voltage For Logic VCC - 2.6 3.3 3.5 V
    Supply Voltage For DCDC converter VCI - 2.6 3.3 3.5 V
    Supply Voltage for Display V16 - - 12.5 13.0 V
    Input High Volt. VIH - 0.9xVCC - VCC V
    Input Low Volt. VIL - GND - 0.1xVCC V
    Output High Volt. VOH IOH=-0.5mA 0.8xVCC - VCC V
    Output Low Volt. VOL IOL=0.5mA GND - 0.2xVCC V
    50% Checkerboard
    Operating Current
    I16 V16=12.5V - 2 4 mA

     

    Specifiche di prodotto
    Size 1.23"
    Resolution 16x2
    Active Area (mm) 30.69x5.94
    Dot Size 0.29x0.31
    Polarizer Glare
    Color White
    Power supply 3.3V
    Display Interface 6800/8080/SPI/I2C
    Display IC WS0012
    Constructive Structure COG
    Frame No
    Touch Panel No touch
    O. Temperature (°C) -40~80
    Data Connection FPC for ZIF Connector
    Pin Nr. 30
    Pin Pitch 0.5mm
    Preferred - Not Preferred Not Preferred
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni