Cerca
Italiano
Catalogo
    Menu Chiudi

    WL0F00043000WGFAASA00-FC

    TFT 4.3" 480x272, UART interface & GPIO Support, 400cd/m², Wide View Angle (IPS), Super extended temperature, Capacitive Touch Panel (GG)
    Brand: Winstar
    Cod.: WL0F00043000WGFAASA00-FC
    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    Prezzo
    €63,30
    €56,90
    €53,50

    Per quantità maggiori di 24pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Disponibile
    €63,30 IVA esclusa
    i h

    DESCRIPTION

    Below are the features of this 4.3 inches Smart Display (UART series):

    1. Input voltage dynamic range 5V to 28V, typical voltage 12V.
    2. Self-testing after booting function.
    3. UART communication interface.
    4. Supports UART protocol, default baud rate at 115200Kbps.
    5. Built in flash memory, store the fonts and pictures.
    6. Support capacitive touch panel (CTP).
    7. Embedded buzzer function.
    8. Demo set HOST can be used on multiple platforms, such as Computer (with USB to UART Dongle), MCU, Raspberry Pi (with PiCAN2).
    9. GPIO PIN support. Supports 8 channe Bi-direction GPIOs TTL 3.3V logic level. The setting functions through PC tools, Smart Display GUI Builder.

      

    DRAWING

     

    SPECIFICATIONS

    General Information

    ItemStandard ValueUnit
    Operating voltage 5~28 Vdc
    Communication Interface UART --
    MCU STM32F750 N/A
    Flash ROM 16 MB
    LCD display size 4.3 inch
    Dot Matrix 480 x 3(RGB) x 272 dot
    Module dimension 119.3(W) x 67.2(H) x 13(D) mm
    Active area 95.04(H) x 53.856(V) mm
    Pixel pitch 0.198(H) x 0.198(V) mm
    Brightness Min: 300; Typ: 400 cd/m2
    LCD type TFT, Normally Black, Transmissive
    View Direction 80/80/80/80
    Aspect Ratio 16:9
    With / Without TP With CTP
    Surface Glare


    Absolute Maximum Ratings

    ItemSymbolMinTypMaxUnit
    Operating Temperature TOP -30 - +80 ℃
    Storage Temperature TST -30 - +80 ℃
    Supply Voltage VIN     +30 V

     

    Electrical Characteristics

    ItemSymbolMinTypMaxUnitRemark
    Supply Voltage VCC 5 12 28 V  
    Supply Current ICC - 180 - mA   
    I/O pin Voltage -- -- -- 3.3 V Note 1
    Note1: Exceed 3.3V may cause MCU damage.

     

    BOM

    ItemDescription
    LCM WF43-­480272WD#APW3-­FC
    PCBA SV10004R300WB00N0101

     

    Interface Pin Function

    CON2 definition

    PinSymbolFunctionRemark
    1 VIN Power +5V~28V Input
    2 GND Power GND Input
    3 Reserve - -
    4 Reserve - -
    5 GND Power GND  Input
    6 GND Power GND  Input
    7 Reserve - -
    8 Reserve - -
    9 VBUS Power Input
    10 UART_RX   Input
    11 UART_TX   Output
    12 GND Power GND Input
    13 VIN Power supply 5V to 28V input Input
    14 Reserve - -
    15 Reserve - -
    16 GND Power GND Input


    CON3 definition

    PinSymbolFunctionRemark
    1 +3V3 3.3V power for SWD interface Output
    2 SWCLK CLK for SWD interface Input
    3 GND GND for SWD interface Output
    4 SWDIO Data pin for SWD interface I/O
    5 NRST Reset pin for SWD interface Input
    6 GND GND for SWD interface Output
    7 WKUP Wake UP (PA0) Input
    8 BOOT0

    --

    Input
    9 IO_0 GPIO (PD4) I/O
    10  IO_1 GPIO (PD5) I/O
    11  IO_2 GPIO (PB4) I/O
    12 IO_3 GPIO (PB5) I/O
    13 IO_4 GPIO (PF9) I/O
    14 IO_5 GPIO (PC1) I/O
    15 IO_6 GPIO (PC4) I/O
    16 IO_7 GPIO (PC5) I/O

     

    Display Usage

    Functional description

    Smart Display can be used to display the coordinate, status and data information provided by the connected HOST device. Customers can configure the position coordinates they want to display in normal operation mode.

    The Display is designed to be easily connected to a controller network, and to use the register type of Holding Register.

    Splash Screen

    The default splash image is shown below.

    This product is produced as a generic product. If you require a custom splash image for your application, contact us to discuss.


    Default Selection

    Press the preferred application and hold for 3 seconds for the first time power on.
     

    Winstar's Smart Display Default Selection


    Acquisition of Displayed Data

    Smart Display uses the Modbus protocol to get and send the data.

    On Config mode, customers can set the coordinates or type of objects; On Display mode, customers can send and get data of objects.

    Configuring the Display

    Winstar Smart Display RS-485 series offers an out-of-the-box Modbus development experience that will lower customers' development costs and speed time-to-market expectations.

    The Smart Display can use wide-temperature are designed to support control applications in harsh operating conditions, which designed to be connected to a variety of different situation combinations, such as automotive, marine, power generation and oil-and-gas.

    The Smart Display comes with standard UI objects to get customers project off the ground quickly. If customers need custom UI objects support, our engineers are here to help. Send over your contents in PNG/JPG format, we will send over a new set of UI objects within 3~5 working days.

    The Smart Display is defined as a slave device, which is controlled by master device via RS485 bus command to render display content on the display screen and return touch event data with protocol objects.

    Example Screen Layout (Industry application)

    The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in an industry application situation.

    Example Screen Layout (Vehicle automotive)

    The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in a vehicle automotive situation.


    Example Screen Layout (Medical application)

    The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in a Medical application situation.

    Specifiche di prodotto
    Size 4.3"
    Resolution 480x272
    Active Area (mm) 95.04x53.85
    Color Full Color
    Power supply 12V
    Display Interface UART + GPIO
    View Angle IPS
    Frame Yes
    Touch Panel Capacitive
    O. Temperature (°C) -30~80
    Preferred - Not Preferred Preferred
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni