Register
Log in
Shopping cart (0)

You have no items in your shopping cart.

Personal menu

Filters

WEO4864W#AP3N00F01-FC

PMOLED 0.71" Graphic 48x64, White color, COG, 3V, Interface I2C, Glare (FPC per Zif)

DRAWING

Winstar Display - 0.71" Graphic OLED 48x64, 0.71 oled

SPECIFICATIONS

Interface Pin Function

No.	Symbol	Function
1	C2P	Positive Terminal of the Flying Inverting Capacitorr Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2	C2N
3	C1P
4	C1N
5	VBAT	Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6	NC	No connection.
7	VSS	Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8	VDD	Power Supply for Logic This is a voltage supply pin. It must be connected to external source.
9	RES#	Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10	SCL	The serial clock input
11	SDA	The serial data input/output
12	IREF	This is segment output current reference pin. When external IREF is used, a resistor should be connected between this pin and Vss to maintain the IREF current at a maximum of 30uA. When internal IREF is used, this pin should be kept NC
13	VCOMH	Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
14	VCC	Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

Mechanical Data

Item	Dimension	Unit
Dot Matrix	48 × 64 Dots	－
Module dimension	13.90 × 22.0 × 1.26	mm
Active Area	10.54 × 14.70	mm
Pixel Size	0.198 × 0.208	mm
Pixel Pitch	0.220 × 0.230	mm
Display Mode	Passive Matrix
Display Color	White
Drive Duty	1/64 Duty
IC	SSD1306
Interface	I2C
Size	0.71 inch

Absolute Maximum Ratings

Parameter	Symbol	Min	Max	Unit
Supply Voltage for Logic	VDD	-0.3	4.0	V
Supply Voltage for Display	VCC	0	15.0	V
Supply Voltage for DC/DC (Internal DC/DC Enable)	VBAT	-0.3	4.3	V
Operating Temperature	TOP	-40	+80	°C
Storage Temperature	TSTG	-40	+85	°C

Electronical Characteristics

Item	Symbol	Condition	Min	Typ	Max	Unit
Supply Voltage for Logic	VDD	－	1.65	3.0	3.3	V
Supply Voltage for Display (Supplied Externally)	VCC	－	7.0	7.5	8.0	V
Charge Pump Regulator Supply Voltage	VBAT	-	3.0	-	4.2	V
Charge Pump Output voltage for Display (Generated by Internal DC/DC)	Charge Pump VCC	-	7.0	7.5	-	V
Input High Volt.	VIH	－	0.8 xVDD	－	VDD	V
Input Low Volt.	VIL	－	0	－	0.2 xVDD	V
Output High Volt.	VOH	－	0.9 xVDD	－	VDD	V
Output Low Volt.	VOL	－	0	－	0.1 xVDD	V
Operating Current for VCC (50% display ON) (VCC Supplied Externally)	ICC	-	-	7	15	mA
50% Check Board operating Current (VCC Generated by Internal DC/DC)	IBAT	-	-	15.0	25.0	mA

SKU: WEO4864W#AP3N00F01-FC

Brand: Winstar

Available: No

Be the first to review this product

Price Breaks

Quantity

10+

25+

Price

€6.50

€5.90

€5.50

€5.40

For quantities above 25 pcs pls send your enquiry to [email protected] or call +39 0332 1888005

€6.50 excl tax

Overview
Specifications
Download
Contact Us

DRAWING

SPECIFICATIONS

Interface Pin Function

No.	Symbol	Function
1	C2P	Positive Terminal of the Flying Inverting Capacitorr Negative Terminal of the Flying Boost Capacitor The charge-pump capacitors are required between the terminals. They must be floated when the converter is not used.
2	C2N
3	C1P
4	C1N
5	VBAT	Power Supply for DC/DC Converter Circuit This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be connected to VDD when the converter is not used.
6	NC	No connection.
7	VSS	Ground of Logic Circuit This is a ground pin. It acts as a reference for the logic pins. It must be connected to external ground.
8	VDD	Power Supply for Logic This is a voltage supply pin. It must be connected to external source.
9	RES#	Power Reset for Controller and Driver This pin is reset signal input. When the pin is low, initialization of the chip is executed.
10	SCL	The serial clock input
11	SDA	The serial data input/output
12	IREF	This is segment output current reference pin. When external IREF is used, a resistor should be connected between this pin and Vss to maintain the IREF current at a maximum of 30uA. When internal IREF is used, this pin should be kept NC
13	VCOMH	Voltage Output High Level for COM Signal This pin is the input pin for the voltage output high level for COM signals. A capacitor should be connected between this pin and VSS.
14	VCC	Power Supply for OEL Panel This is the most positive voltage supply pin of the chip. A stabilization capacitor should be connected between this pin and VSS when the converter is used. It must be connected to external source when the converter is not used.

Mechanical Data

Item	Dimension	Unit
Dot Matrix	48 × 64 Dots	－
Module dimension	13.90 × 22.0 × 1.26	mm
Active Area	10.54 × 14.70	mm
Pixel Size	0.198 × 0.208	mm
Pixel Pitch	0.220 × 0.230	mm
Display Mode	Passive Matrix
Display Color	White
Drive Duty	1/64 Duty
IC	SSD1306
Interface	I2C
Size	0.71 inch

Absolute Maximum Ratings

Parameter	Symbol	Min	Max	Unit
Supply Voltage for Logic	VDD	-0.3	4.0	V
Supply Voltage for Display	VCC	0	15.0	V
Supply Voltage for DC/DC (Internal DC/DC Enable)	VBAT	-0.3	4.3	V
Operating Temperature	TOP	-40	+80	°C
Storage Temperature	TSTG	-40	+85	°C

Electronical Characteristics

Item	Symbol	Condition	Min	Typ	Max	Unit
Supply Voltage for Logic	VDD	－	1.65	3.0	3.3	V
Supply Voltage for Display (Supplied Externally)	VCC	－	7.0	7.5	8.0	V
Charge Pump Regulator Supply Voltage	VBAT	-	3.0	-	4.2	V
Charge Pump Output voltage for Display (Generated by Internal DC/DC)	Charge Pump VCC	-	7.0	7.5	-	V
Input High Volt.	VIH	－	0.8 xVDD	－	VDD	V
Input Low Volt.	VIL	－	0	－	0.2 xVDD	V
Output High Volt.	VOH	－	0.9 xVDD	－	VDD	V
Output Low Volt.	VOL	－	0	－	0.1 xVDD	V
Operating Current for VCC (50% display ON) (VCC Supplied Externally)	ICC	-	-	7	15	mA
50% Check Board operating Current (VCC Generated by Internal DC/DC)	IBAT	-	-	15.0	25.0	mA

Products specifications

Brand	Winstar
Size	0.71"
Resolution	48x64
Active Area (mm)	10.54x14.70
Dot Size	0.19x0.20
Polarizer	Glare
Color	White
Power supply	3V
Display Interface	I2C
Display IC	SSD1306
Constructive Structure	COG
Frame	No
Touch Panel	No touch
O. Temperature (°C)	-40~80
Display Connection	FPC for ZIF Connector
Pin Nr.	14
Pin Pitch	0.5mm
Preferred - Not Preferred	Preferred

Download

Your name

Your email

Enquiry

Products specifications

Brand	Winstar
Size	0.71"
Resolution	48x64
Active Area (mm)	10.54x14.70
Dot Size	0.19x0.20
Polarizer	Glare
Color	White
Power supply	3V
Display Interface	I2C
Display IC	SSD1306
Constructive Structure	COG
Frame	No
Touch Panel	No touch
O. Temperature (°C)	-40~80
Display Connection	FPC for ZIF Connector
Pin Nr.	14
Pin Pitch	0.5mm
Preferred - Not Preferred	Preferred