Menu
Search
Filters
Close
Menu

WFN0240DA2#0NX0-FC

Picture of WFN0240DA2#0NX0-FC Picture of WFN0240DA2#0NX0-FC
TFT 2.4" 240x320 Portrait LCD Panel, Transflective, Interface MCU (RGB/Parallel/SPI) IC ST7789, 250cd/m², No touch

DESCRIPTION

The WINSTAR WFN0240DA2#0NX0-FC is a color active matrix TFT (Thin Film Transistor) LCD (liquid crystal display) that uses amorphous silicon TFT as a switching device. This module is composed of a transflective type TFT-LCD Panel, driver circuit, back-light unit. The resolution of a 2.4’TFT-LCD contains 240X320 pixels, and can display up to 65K/262K colors. 

 

DRAWING

SPECIFICATIONS

General Specifications

ItemDimensionUnit
Size 2.4 inch
Dot Matrix 240 × RGB × 320(TFT) dots
Module dimension 42.72 × 60.26 × 2.63 mm
Active area 36.72 × 48.96 mm
Pixel Pitch 0.153 × 0.153 mm
LCD type TFT, Normally White, Transflective
Viewing Direction 3 O'clock
TFT Interface 8/9/16/18Bit MCU
3/4SPI+16/18Bit RGB
3-line/4-line Serial
Backlight Type LED, Normally White
TFT Driver IC ST7789 or Equivalent
Touch Panel Without Touch Panel
Surface Anti-Glare

 

Absolute Maximum Ratings

ItemSymbolMinTypMaxUnit
Operating Temperature TOP -20 － +60 ℃
Storage Temperature TST -30 － +70 ℃

 

Electrical Characteristics

Operating conditions

CharacteristicsSymbolMin.Typ.Max.Unit
Digital Supply Voltage VCI 2.4 3.3 3.6 V
Supply Voltage (Logic) IOVCC 1.65 1.8 3.3 V
Normal mode Current consumption IDD -- 5 10 mA
Level input voltage VIH 0.7 IOVCC   IOVCC V
VIL GND   0.3 IOVCC V
Level output voltage VOH 0.8 IOVCC   IOVCC V
VOL GND   0.2 IOVCC V
 

LED driving conditions

ItemSymbolMin.Typ.Max.Unit
LED current - - 80 - mA
LED voltage VLEDA 2.7 3.1 3.3 V
LED Life Time - 50,000 - - Hr

 

Interface Pin Function

LCM PIN Definition

Pin NoSymbolDescriptionI/O
1 NC No connection --
2 NC No connection --
3 NC No connection --
4 NC No connection --
5 GND Ground. P
6 GND Ground. P
7 VCC Supply voltage(3.3V). I
8 VCC Supply voltage(3.3V). I
9 IOVCC Power Supply for I/O System. I
10 SDO SPI interface output pin.
-The data is output on the falling edge of the SCL signal.
-If not used, let this pin open.		 O
11-28 DB17-DB0 18-bit parallel bi-directional data bus for MCU system and RGB i
nterface mode. Fix to GND level when not in use		 I/O
29 DIN(SDA) Serial input signal.
The data is latched on the rising edge of the SCL signal. fix this pin at IOVCC or GND when not in use.		 I/O
30 PCLK Dot clock signal for RGB interface operation.
Fix this pin at IOVCC or GND when not in use.		 I
31 DE Data enable signal for RGB interface operation.
fix this pin at IOVCC or GND when not in use.		 I
32 HSYNC Line synchronizing signal for RGB interface operation.
fix this pin at IOVCC or GND when not in use.		 I
33 VSYNC Frame synchronizing signal for RGB interface operation.
fix this pin at IOVCC or GND when not in use.		 I
34 RD Read enable in 8080 MCU parallel interface.
-If not used, please fix this pin at IOVCC or DGND.		 I
35 WR(SPI-RS) -Write enable in MCU parallel interface.
Display data/command selection pin in 4-line serial interface.
Second Data lane in 2 data lane serial interface.
-If not used, please fix this pin at IOVCC or DGND.		 I
36 RS(SPI-SCL) -Display data/command selection pin in parallel interface.
-This pin is used to be serial interface clock. RS=’1’: display data or parameter.
RS=’0’: command data.
-If not used, please fix this pin at IOVCC or DGND.		 I
37 CS Chip select input pin (“Low” enable).
fix this pin at IOVCC or GND when not in use.		 I
38 RESET This signal will reset the device and must be applied to properly
initialize the chip.		 I
39 IM0 18-bit parallel bi-directional data bus for MCU system and RGB
interface mode. Fix to GND level when not in use		 I
40 IM1
41 IM2
42 NC No connection -
43 LEDA Anode pin of backlight P
44 NC No connection -
45 LEDK Cathode pin OF backlight

Note: MCU interface SET for IM PINS.

 

IM2IM1IM0Interface typeDB Pin in use
0 0 0 80-16bit interface DB7-DB0
0 0 1 80-8bit interface DB15-DB0
0 1 0 80-18bit interface DB8-DB0
0 1 1 80-9bit interface DB17-DB0
1 0 1 3-Wire 9bit data serial interface SDA SCL CS
1 1 0 4-Wire 8bit data serial interface SDA SCL CS RS

1. If not use PIN, fix to the GND, IOVCC or NC.
2. If use RGB mode must select serial interface.

SKU: WFN0240DA2#0NX0-FC
Brand: Winstar
Available: No
Be the first to review this product
Price Breaks
Quantity
1+
5+
10+
25+
Price
€30.10
€24.10
€11.00
€10.60

For quantities above 25 pcs pls send your enquiry to [email protected] or call +39 0332 1888005

€30.10 excl tax

DESCRIPTION

The WINSTAR WFN0240DA2#0NX0-FC is a color active matrix TFT (Thin Film Transistor) LCD (liquid crystal display) that uses amorphous silicon TFT as a switching device. This module is composed of a transflective type TFT-LCD Panel, driver circuit, back-light unit. The resolution of a 2.4’TFT-LCD contains 240X320 pixels, and can display up to 65K/262K colors. 

 

DRAWING

SPECIFICATIONS

General Specifications

ItemDimensionUnit
Size 2.4 inch
Dot Matrix 240 × RGB × 320(TFT) dots
Module dimension 42.72 × 60.26 × 2.63 mm
Active area 36.72 × 48.96 mm
Pixel Pitch 0.153 × 0.153 mm
LCD type TFT, Normally White, Transflective
Viewing Direction 3 O'clock
TFT Interface 8/9/16/18Bit MCU
3/4SPI+16/18Bit RGB
3-line/4-line Serial
Backlight Type LED, Normally White
TFT Driver IC ST7789 or Equivalent
Touch Panel Without Touch Panel
Surface Anti-Glare

 

Absolute Maximum Ratings

ItemSymbolMinTypMaxUnit
Operating Temperature TOP -20 － +60 ℃
Storage Temperature TST -30 － +70 ℃

 

Electrical Characteristics

Operating conditions

CharacteristicsSymbolMin.Typ.Max.Unit
Digital Supply Voltage VCI 2.4 3.3 3.6 V
Supply Voltage (Logic) IOVCC 1.65 1.8 3.3 V
Normal mode Current consumption IDD -- 5 10 mA
Level input voltage VIH 0.7 IOVCC   IOVCC V
VIL GND   0.3 IOVCC V
Level output voltage VOH 0.8 IOVCC   IOVCC V
VOL GND   0.2 IOVCC V
 

LED driving conditions

ItemSymbolMin.Typ.Max.Unit
LED current - - 80 - mA
LED voltage VLEDA 2.7 3.1 3.3 V
LED Life Time - 50,000 - - Hr

 

Interface Pin Function

LCM PIN Definition

Pin NoSymbolDescriptionI/O
1 NC No connection --
2 NC No connection --
3 NC No connection --
4 NC No connection --
5 GND Ground. P
6 GND Ground. P
7 VCC Supply voltage(3.3V). I
8 VCC Supply voltage(3.3V). I
9 IOVCC Power Supply for I/O System. I
10 SDO SPI interface output pin.
-The data is output on the falling edge of the SCL signal.
-If not used, let this pin open.		 O
11-28 DB17-DB0 18-bit parallel bi-directional data bus for MCU system and RGB i
nterface mode. Fix to GND level when not in use		 I/O
29 DIN(SDA) Serial input signal.
The data is latched on the rising edge of the SCL signal. fix this pin at IOVCC or GND when not in use.		 I/O
30 PCLK Dot clock signal for RGB interface operation.
Fix this pin at IOVCC or GND when not in use.		 I
31 DE Data enable signal for RGB interface operation.
fix this pin at IOVCC or GND when not in use.		 I
32 HSYNC Line synchronizing signal for RGB interface operation.
fix this pin at IOVCC or GND when not in use.		 I
33 VSYNC Frame synchronizing signal for RGB interface operation.
fix this pin at IOVCC or GND when not in use.		 I
34 RD Read enable in 8080 MCU parallel interface.
-If not used, please fix this pin at IOVCC or DGND.		 I
35 WR(SPI-RS) -Write enable in MCU parallel interface.
Display data/command selection pin in 4-line serial interface.
Second Data lane in 2 data lane serial interface.
-If not used, please fix this pin at IOVCC or DGND.		 I
36 RS(SPI-SCL) -Display data/command selection pin in parallel interface.
-This pin is used to be serial interface clock. RS=’1’: display data or parameter.
RS=’0’: command data.
-If not used, please fix this pin at IOVCC or DGND.		 I
37 CS Chip select input pin (“Low” enable).
fix this pin at IOVCC or GND when not in use.		 I
38 RESET This signal will reset the device and must be applied to properly
initialize the chip.		 I
39 IM0 18-bit parallel bi-directional data bus for MCU system and RGB
interface mode. Fix to GND level when not in use		 I
40 IM1
41 IM2
42 NC No connection -
43 LEDA Anode pin of backlight P
44 NC No connection -
45 LEDK Cathode pin OF backlight

Note: MCU interface SET for IM PINS.

 

IM2IM1IM0Interface typeDB Pin in use
0 0 0 80-16bit interface DB7-DB0
0 0 1 80-8bit interface DB15-DB0
0 1 0 80-18bit interface DB8-DB0
0 1 1 80-9bit interface DB17-DB0
1 0 1 3-Wire 9bit data serial interface SDA SCL CS
1 1 0 4-Wire 8bit data serial interface SDA SCL CS RS

1. If not use PIN, fix to the GND, IOVCC or NC.
2. If use RGB mode must select serial interface.

Products specifications
Brand Winstar
Size 2.4"
Resolution 240x320
Active Area (mm) 36.72x48.96
Color Full Color
Display Interface MCU (RGB/Parallel/SPI)
Display IC ST7789
View Angle TN
Sunlight Readable Transflective
Frame No
Touch Panel No touch
O. Temperature (°C) -20~60
Display Connection FPC for ZIF Connector
Pin Nr. 45
Pin Pitch 0.5mm
Preferred - Not Preferred Preferred
Download
Products specifications
Brand Winstar
Size 2.4"
Resolution 240x320
Active Area (mm) 36.72x48.96
Color Full Color
Display Interface MCU (RGB/Parallel/SPI)
Display IC ST7789
View Angle TN
Sunlight Readable Transflective
Frame No
Touch Panel No touch
O. Temperature (°C) -20~60
Display Connection FPC for ZIF Connector
Pin Nr. 45
Pin Pitch 0.5mm
Preferred - Not Preferred Preferred
Categories
Recently viewed
Contacts
  • +39 0332 1888005
  • +39 0332 320856
  • Via 2 Giugno, 20 – 21022 Azzate (VA) Italy
  • VAT number IT02764420127
    REA Varese 285686
    Social capital fully paid 100.000€
Information
Featured Products
Copyright © 2026 FIRST Components. All rights reserved.
Powered by nopCommerce
Developed by Weblink
FIRST Components s.r.l.
Via 2 Giugno, 20 – 21022 Azzate (VA) Italy