Menu
Search
Filters
Close
Menu

WEO12864W#AEA3N00000-FC

Picture of WEO12864W#AEA3N00000-FC Picture of WEO12864W#AEA3N00000-FC
PMOLED 1.54'' Graphic 128x64, White color, COG, 3V, Interface 6800,8080,SPI,I2C, CH1116 IC, Anti-glare

DESCRIPTION

1.54-inch COG 128x64 Graphic OLED display. This module is built-in with CH1116 IC; it can be communicated via I2C, 4-line SPI, 6800 or 8080 parallel interface; supply voltage for logic is 3V (typical value), the supply voltage for display 12.5V (typical value), 1/64 driving duty. This series has different ZIF FPC; currently, we provide 24 pins and 30 pins optional if customs require custom FPC, welcome to contact us.

This model is ideal for IoT systems, smart home applications, financial-POS, intelligent technology devices, energy systems, communication systems, medical instruments, etc. This module can be operating at temperatures from -40℃ to +80℃; its storage temperatures range from -40℃ to +85℃.

DRAWING

SPECIFICATIONS

Interface Pin Function

No.SymbolFunction
1 NC(GND) No connection
2 VSS Ground.
3 VSS Ground.
4 NC No connection
5 VDD1 Power supply input
6 IM1 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI
IM1 1 1 0 0
IM2 1 0 1 0
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD1
7 IM2
8 CS# This pad is the chip select input. When CS# = “L”, then the chip select becomes active, and data/command I/O is enabled.
9 RES# This is a reset signal input pad. When RES# is set to “L”, the settings are initialized. The reset operation is performed by the RES# signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 WR#
(R/W#)		 This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR# signal. The signals on the data bus are latched at the rising edge of the WR# signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W#= “H”: Read.
When R/W#= “L”: Write.
12 E/RD# This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD# signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD# = “H”: Enable.
When RD# = “L”: Disable.
13-20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
21 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
22 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
23 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
24 NC(GND) No connection

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 128 × 64 dots
Module dimension 42.04 × 27.22 × 1.41 mm
Active Area 35.05 × 17.51 mm
Pixel Size 0.249 × 0.249 mm
Pixel Pitch 0.274 × 0.274 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/64 Duty
IC CH1116
Interface 6800,8080,4-wire SPI,I2C
Size 1.54 inch

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage for Logic VDD -0.3 3.6 V
Supply Voltage for Display VCC 0 14.5 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C

 

Electronical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD1 － 1.65 3.0 3.3 V
Supply Voltage for Display VPP － 6.4 12.5 13.0 V
High Level Input VIH － 0.8×VDD1 － VDD1 V
Low Level Input VIL － VSS － 0.2×VDD1 V
High Level Output VOH － 0.8×VDD1 － VDD1 V
Low Level Output VOL － VSS － 0.2×VDD1 V
Display 50% Pixel on IPP VPP =12.5V － 8 12 mA

 

SKU: WEO12864W#AEA3N00000-FC
Brand: Winstar
Available: No
Be the first to review this product
Accessory Kit
Price Breaks
Quantity
1+
5+
10+
25+
Price
€10.80
€7.90
€7.60
€7.30

For quantities above 25 pcs pls send your enquiry to sales@first-components.com or call +39 0332 1888005

€10.80 excl tax

DESCRIPTION

1.54-inch COG 128x64 Graphic OLED display. This module is built-in with CH1116 IC; it can be communicated via I2C, 4-line SPI, 6800 or 8080 parallel interface; supply voltage for logic is 3V (typical value), the supply voltage for display 12.5V (typical value), 1/64 driving duty. This series has different ZIF FPC; currently, we provide 24 pins and 30 pins optional if customs require custom FPC, welcome to contact us.

This model is ideal for IoT systems, smart home applications, financial-POS, intelligent technology devices, energy systems, communication systems, medical instruments, etc. This module can be operating at temperatures from -40℃ to +80℃; its storage temperatures range from -40℃ to +85℃.

DRAWING

SPECIFICATIONS

Interface Pin Function

No.SymbolFunction
1 NC(GND) No connection
2 VSS Ground.
3 VSS Ground.
4 NC No connection
5 VDD1 Power supply input
6 IM1 These are the MPU interface mode select pads.
  8080 I2C 6800 4-wire SPI
IM1 1 1 0 0
IM2 1 0 1 0
Note
(1) 0 is connected to VSS
(2) 1 is connected to VDD1
7 IM2
8 CS# This pad is the chip select input. When CS# = “L”, then the chip select becomes active, and data/command I/O is enabled.
9 RES# This is a reset signal input pad. When RES# is set to “L”, the settings are initialized. The reset operation is performed by the RES# signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 WR#
(R/W#)		 This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR# signal. The signals on the data bus are latched at the rising edge of the WR# signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W#= “H”: Read.
When R/W#= “L”: Write.
12 E/RD# This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD# signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU, this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD# = “H”: Enable.
When RD# = “L”: Disable.
13-20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
21 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
22 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
23 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
24 NC(GND) No connection

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 128 × 64 dots
Module dimension 42.04 × 27.22 × 1.41 mm
Active Area 35.05 × 17.51 mm
Pixel Size 0.249 × 0.249 mm
Pixel Pitch 0.274 × 0.274 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/64 Duty
IC CH1116
Interface 6800,8080,4-wire SPI,I2C
Size 1.54 inch

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage for Logic VDD -0.3 3.6 V
Supply Voltage for Display VCC 0 14.5 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C

 

Electronical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD1 － 1.65 3.0 3.3 V
Supply Voltage for Display VPP － 6.4 12.5 13.0 V
High Level Input VIH － 0.8×VDD1 － VDD1 V
Low Level Input VIL － VSS － 0.2×VDD1 V
High Level Output VOH － 0.8×VDD1 － VDD1 V
Low Level Output VOL － VSS － 0.2×VDD1 V
Display 50% Pixel on IPP VPP =12.5V － 8 12 mA

 

Products specifications
Brand Winstar
Size 1.54"
Resolution 128x64
Active Area (mm) 35.05x17.51
Dot Size 0.24x0.24
Polarizer Anti-glare
Color White
Power supply 3V
Display Interface 6800/8080/SPI/I2C
Display IC CH1116
Constructive Structure COG
Frame No
Touch Panel No touch
O. Temperature (°C) -40~80
Display Connection FPC per ZIF Connector
Pin Nr. 24
Pin Pitch 0.5mm
Preferred - Not Preferred Preferred
Download
Products specifications
Brand Winstar
Size 1.54"
Resolution 128x64
Active Area (mm) 35.05x17.51
Dot Size 0.24x0.24
Polarizer Anti-glare
Color White
Power supply 3V
Display Interface 6800/8080/SPI/I2C
Display IC CH1116
Constructive Structure COG
Frame No
Touch Panel No touch
O. Temperature (°C) -40~80
Display Connection FPC per ZIF Connector
Pin Nr. 24
Pin Pitch 0.5mm
Preferred - Not Preferred Preferred
Related products
Picture of MOLEX_52437-2433

MOLEX_52437-2433

ZIF Connector 24 pins, 0.5mm pitch, Bottom contact
From €3.00 excl tax
Picture of WEA12864W#A01-FC

WEA12864W#A01-FC

PMOLED 1.54'' Graphic 128x64, Yellow, COG + PCB, IC SSD1309, 3~5V, Interface SPI, Anti-glare
From €12.90 excl tax
Picture of TSL012864AF191XXXX00

TSL012864AF191XXXX00

Capacitive Touch panel 1.54'', O.D. 43.04x28.22mm for PMOLED, I2C interface, Detect point 1 finger, Glass-Glass structure, FPC per ZIF Connector (WEO012864A // WEO012864AE OLED families)
From €13.40 excl tax
Categories
Recently viewed
Contacts
  • +39 0332 1888005
  • +39 0332 320856
  • Via 2 Giugno, 20 – 21022 Azzate (VA) Italy
  • VAT number IT02764420127
    REA Varese 285686
    Social capital fully paid 100.000€
Information
Featured Products
Copyright © 2023 FIRST Components. All rights reserved.
Powered by nopCommerce
Developed by Weblink
FIRST Components s.r.l.
Via 2 Giugno, 20 – 21022 Azzate (VA) Italy
;