Cerca
Filters
Close

WEO12832W#NP3N00000-FC

PMOLED 2.22" Graphic 128x32, White color, COG, 3V, Interface 6800,8080,SPI,I2C, SH1106 IC, Glare (FPC per ZIF Connector)

DRAWING

 

SPECIFICATIONS

Interface Pin Function

No.SymbolFunction
1 N.C.(GND) No connection.
2~3 VSS Ground.
4 N.C. No connection.
5 VDD1 Power supply input.
6 IM1
 8080I2C68004-SPI
IM1 1 1 0 0
IM2 1 0 1 0
These are the MPU interface mode select pads.
7 IM2
8 ___
CS
This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
9 ___
RES
This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 ___
WR
This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.
12    ___
E/RD
This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD = “H”: Enable.
When RD = “L”: Disable.
13~20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
21 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
22 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
23 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
24 NC(GND) No connection.

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 128 × 32 Dots
Module dimension 62.0 × 24.0 × 2.17 mm
Active Area 55.016 × 13.096 mm
Pixel Size 0.406 × 0.386 mm
Pixel Pitch 0.43 × 0.41 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/32 Duty
IC SH1106
Interface 6800,8080,4-Wire SPI,I2C
Size 2.23 inch

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage For Logic VDD1-VSS -0.3 3.6 V
Supply Voltage for Display VPP -0.3 14.5 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C

 

Electronical Characteristics

DC Electrical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD1 1.65 3.0 3.3 V
Supply Voltage for Display VPP 6.4 12.0 12.5 V
Input High Volt. VIH 0.8XVDD1 VDD1 V
Input Low Volt. VIL VSS 0.2xVDD1 V
Output High Volt. VOH 0.8xVDD1 VDD1 V
Output Low Volt. VOL VSS 0.2xVDD1 V
Display 50% Pixel On IPP VPP=12V 15 30 mA
 

SKU: WEO12832W#NP3N00000-FC
Brand: Winstar
Disponibile: No
Kit Accessori
Prezzi per quantità
Quantità
1+
5+
10+
25+
Prezzo
€13,30
€9,80
€9,40
€9,10

Per quantita’ maggiori di 25pz prego invii la richiesta a sales@first-components.com o chiami il +39 0332 1888005

€13,30 IVA esclusa

DRAWING

 

SPECIFICATIONS

Interface Pin Function

No.SymbolFunction
1 N.C.(GND) No connection.
2~3 VSS Ground.
4 N.C. No connection.
5 VDD1 Power supply input.
6 IM1
 8080I2C68004-SPI
IM1 1 1 0 0
IM2 1 0 1 0
These are the MPU interface mode select pads.
7 IM2
8 ___
CS
This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
9 ___
RES
This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 ___
WR
This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.
12    ___
E/RD
This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD = “H”: Enable.
When RD = “L”: Disable.
13~20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
21 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
22 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
23 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
24 NC(GND) No connection.

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 128 × 32 Dots
Module dimension 62.0 × 24.0 × 2.17 mm
Active Area 55.016 × 13.096 mm
Pixel Size 0.406 × 0.386 mm
Pixel Pitch 0.43 × 0.41 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/32 Duty
IC SH1106
Interface 6800,8080,4-Wire SPI,I2C
Size 2.23 inch

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage For Logic VDD1-VSS -0.3 3.6 V
Supply Voltage for Display VPP -0.3 14.5 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C

 

Electronical Characteristics

DC Electrical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD1 1.65 3.0 3.3 V
Supply Voltage for Display VPP 6.4 12.0 12.5 V
Input High Volt. VIH 0.8XVDD1 VDD1 V
Input Low Volt. VIL VSS 0.2xVDD1 V
Output High Volt. VOH 0.8xVDD1 VDD1 V
Output Low Volt. VOL VSS 0.2xVDD1 V
Display 50% Pixel On IPP VPP=12V 15 30 mA
 

Specifiche di prodotto
Brand Winstar
Size 2.22"
Risoluzione 128x32
Area Attiva (mm) 55.01x13.09
Dot Size 0.40x0.38
Polarizzatore Glare
Colore White
Alimentazione 3V
Interfaccia Display 6800/8080/SPI/I2C
Display IC SH1106
Struttura Costruttiva COG
Frame No
Touch Panel No touch
Temperatura O. (°C) -40~80
Connessione Display FPC per ZIF Connector
Nr. Pin 24
Passo Pin 0.5mm
Preferred - Not Preferred Preferred
Download
Specifiche di prodotto
Brand Winstar
Size 2.22"
Risoluzione 128x32
Area Attiva (mm) 55.01x13.09
Dot Size 0.40x0.38
Polarizzatore Glare
Colore White
Alimentazione 3V
Interfaccia Display 6800/8080/SPI/I2C
Display IC SH1106
Struttura Costruttiva COG
Frame No
Touch Panel No touch
Temperatura O. (°C) -40~80
Connessione Display FPC per ZIF Connector
Nr. Pin 24
Passo Pin 0.5mm
Preferred - Not Preferred Preferred
;