Menu
Search
Filters
Close
Menu

WEO12832W#NP3N00000-FC

Picture of WEO12832W#NP3N00000-FC Picture of WEO12832W#NP3N00000-FC
PMOLED 2.22" Graphic 128x32, White color, COG, 3V, Interface 6800,8080,SPI,I2C, SH1106 IC, Glare (FPC per ZIF Connector)

DRAWING

 

SPECIFICATIONS

Interface Pin Function

No.SymbolFunction
1 N.C.(GND) No connection.
2~3 VSS Ground.
4 N.C. No connection.
5 VDD1 Power supply input.
6 IM1
 8080I2C68004-SPI
IM1 1 1 0 0
IM2 1 0 1 0
These are the MPU interface mode select pads.
7 IM2
8 ___
CS		 This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
9 ___
RES		 This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 ___
WR		 This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.
12    ___
E/RD		 This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD = “H”: Enable.
When RD = “L”: Disable.
13~20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
21 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
22 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
23 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
24 NC(GND) No connection.

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 128 × 32 Dots －
Module dimension 62.0 × 24.0 × 2.17 mm
Active Area 55.016 × 13.096 mm
Pixel Size 0.406 × 0.386 mm
Pixel Pitch 0.43 × 0.41 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/32 Duty
IC SH1106
Interface 6800,8080,4-Wire SPI,I2C
Size 2.23 inch

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage For Logic VDD1-VSS -0.3 3.6 V
Supply Voltage for Display VPP -0.3 14.5 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C

 

Electronical Characteristics

DC Electrical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD1 － 1.65 3.0 3.3 V
Supply Voltage for Display VPP － 6.4 12.0 12.5 V
Input High Volt. VIH － 0.8XVDD1 － VDD1 V
Input Low Volt. VIL － VSS － 0.2xVDD1 V
Output High Volt. VOH － 0.8xVDD1 － VDD1 V
Output Low Volt. VOL － VSS － 0.2xVDD1 V
Display 50% Pixel On IPP VPP=12V － 15 30 mA
 

SKU: WEO12832W#NP3N00000-FC
Brand: Winstar
Available: Yes
Be the first to review this product
Accessory Kit
Price Breaks
Quantity
1+
5+
10+
25+
Price
€12.80
€9.40
€9.10
€8.80

For quantities above 25 pcs pls send your enquiry to [email protected] or call +39 0332 1888005

€12.80 excl tax

DRAWING

 

SPECIFICATIONS

Interface Pin Function

No.SymbolFunction
1 N.C.(GND) No connection.
2~3 VSS Ground.
4 N.C. No connection.
5 VDD1 Power supply input.
6 IM1
 8080I2C68004-SPI
IM1 1 1 0 0
IM2 1 0 1 0
These are the MPU interface mode select pads.
7 IM2
8 ___
CS		 This pad is the chip select input. When CSB = “L”, then the chip select becomes active, and data/command I/O is enabled.
9 ___
RES		 This is a reset signal input pad. When RES is set to “L”, the settings are initialized. The reset operation is performed by the RES signal level.
10 A0 This is the Data/Command control pad that determines whether the data bits are data or a command.
A0 = “H”: the inputs at D0 to D7 are treated as display data.
A0 = “L”: the inputs at D0 to D7 are transferred to the command registers.
In I2C interface, this pad serves as SA0 to distinguish the different address of OLED driver.
11 ___
WR		 This is a MPU interface input pad.
When connected to an 8080 MPU, this is active LOW. This pad connects to the 8080 MPU WR signal. The signals on the data bus are latched at the rising edge of the WR signal.
When connected to a 6800 Series MPU: This is the read/write control signal input terminal.
When R/W = “H”: Read.
When R/W = “L”: Write.
12    ___
E/RD		 This is a MPU interface input pad.
When connected to an 8080 series MPU, it is active LOW. This pad is connected to the RD signal of the 8080 series MPU, and the data bus is in an output status when this signal is “L”.
When connected to a 6800 series MPU , this is active HIGH. This is used as an enable clock input of the 6800 series MPU.
When RD = “H”: Enable.
When RD = “L”: Disable.
13~20 D0~D7 This is an 8-bit bi-directional data bus that connects to an 8-bit or 16-bit standard MPU data bus.
When the serial interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SI). At this time, D2 to D7 are set to high impedance.
When the I2C interface is selected, then D0 serves as the serial clock input pad (SCL) and D1 serves as the serial data input pad (SDAI). At this time, D2 to D7 are set to high impedance.
21 IREF This is a segment current reference pad. A resistor should be connected between this pad and VSS. Set the current at 18.75uA.
22 VCOMH This is a pad for the voltage output high level for common signals.
A capacitor should be connected between this pad and VSS.
23 VPP OLED panel power supply. Generated by internal charge pump.
Connect to capacitor. It could be supplied externally.
24 NC(GND) No connection.

 

Mechanical Data

ItemDimensionUnit
Dot Matrix 128 × 32 Dots －
Module dimension 62.0 × 24.0 × 2.17 mm
Active Area 55.016 × 13.096 mm
Pixel Size 0.406 × 0.386 mm
Pixel Pitch 0.43 × 0.41 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/32 Duty
IC SH1106
Interface 6800,8080,4-Wire SPI,I2C
Size 2.23 inch

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage For Logic VDD1-VSS -0.3 3.6 V
Supply Voltage for Display VPP -0.3 14.5 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C

 

Electronical Characteristics

DC Electrical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD1 － 1.65 3.0 3.3 V
Supply Voltage for Display VPP － 6.4 12.0 12.5 V
Input High Volt. VIH － 0.8XVDD1 － VDD1 V
Input Low Volt. VIL － VSS － 0.2xVDD1 V
Output High Volt. VOH － 0.8xVDD1 － VDD1 V
Output Low Volt. VOL － VSS － 0.2xVDD1 V
Display 50% Pixel On IPP VPP=12V － 15 30 mA
 

Products specifications
Brand Winstar
Size 2.22"
Resolution 128x32
Active Area (mm) 55.01x13.09
Dot Size 0.40x0.38
Polarizer Glare
Color White
Power supply 3V
Display Interface 6800/8080/SPI/I2C
Display IC SH1106
Constructive Structure COG
Frame No
Touch Panel No touch
O. Temperature (°C) -40~80
Display Connection FPC for ZIF Connector
Pin Nr. 24
Pin Pitch 0.5mm
Preferred - Not Preferred Preferred
Download
Products specifications
Brand Winstar
Size 2.22"
Resolution 128x32
Active Area (mm) 55.01x13.09
Dot Size 0.40x0.38
Polarizer Glare
Color White
Power supply 3V
Display Interface 6800/8080/SPI/I2C
Display IC SH1106
Constructive Structure COG
Frame No
Touch Panel No touch
O. Temperature (°C) -40~80
Display Connection FPC for ZIF Connector
Pin Nr. 24
Pin Pitch 0.5mm
Preferred - Not Preferred Preferred
Related products
Picture of MOLEX_52437-2433

MOLEX_52437-2433

ZIF Connector 24 pins, 0.5mm pitch, Bottom contact
From €3.00 excl tax
Picture of WEO12832W#A00-FC

WEO12832W#A00-FC

PMOLED 2.22" Graphic 128x32, White color, COG, 3V, Interface 6800,8080,SPI,I2C, SSD1305 IC, Glare (FPC per ZIF Connector)
From €10.10 excl tax
Picture of WWOLEDUSBDEMO-165#

WWOLEDUSBDEMO-165#

Evaluation kit for PMOLED COG Character and Graphics
Quote request
Categories
Recently viewed
Contacts
  • +39 0332 1888005
  • +39 0332 320856
  • Via 2 Giugno, 20 – 21022 Azzate (VA) Italy
  • VAT number IT02764420127
    REA Varese 285686
    Social capital fully paid 100.000€
Information
Featured Products
Copyright © 2025 FIRST Components. All rights reserved.
Powered by nopCommerce
Developed by Weblink
FIRST Components s.r.l.
Via 2 Giugno, 20 – 21022 Azzate (VA) Italy