WL0F00101000JNAACSA00-FC

General Specifications 

General information

Item	Standard Value	Unit
Operating voltage	8V~28V dynamic	Vdc
Communication Interface	CAN bus	Vpp
MCU	STM32F746	N/A
Flash Memory	16	MB
LCD display size	10.1	inch
Dot Matrix	1024 x RGB x 600(TFT)	dots
Module dimension	248.8(W) x 143(H) x 20(D)	mm
Active area	222.72 (H) x 125.28(V)	mm
Dot pitch	0.2175(W) x 0.2088(H)	mm
Brightness	Min: 500; Typ: 500
LCD type	LED, Normally Black, Transmissive
View Direction	85/85/85/85
Aspect Ratio	16:9
Touch Panel	Withuot TP
Surface	Anti-Glare

Absolute Maximum Ratings

Item	Symbol	Min	Typ	Max	Unit
Operating Temperature	TOP	-20	－	+70	℃
Storage Temperature	TST	-30	－	+80	℃

Electrical Characteristics

Item	Symbol	Condition	Min	Typ	Max	Unit
Supply Voltage	VCC	－	8	12	28	V
Supply LCM current	I(mA)	-	-	550	-	mA

 BOM

Item	Description
LCM	WF101­1024600JL#0P0­FC
PCBA	SV10010R100JC00N0102

 

Interface Pin Function

CON1 definition

Pin	Symbol	Function
1	VIN	Power supply 8V to 28V input
2	GND	Power supply GND input
3	CAN_H	CAN bus D+
4	CAN_L	CAN bus D-
5	GND	Power supply GND input
6	GND	Power supply GND input
7	Reserve	USB_D-
8	Reserve	USB_D+
9	NC	-
10	Reserve	USART RX interface(Reserve)
11	Reserve	USART TX interface(Reserve)
12	GND	Power supply GND input
13	VIN	Power supply 8V to 28V input
14	NC	-
15	NC	-
16	GND	Power supply GND input

CON2 definition

Pin	Symbol	Function	Remark
1	3V3	3.3V power for JTAG interface	Output
2	SWCLK	CLK pin for JTAG interface	Input
3	GND	GND for JTAG interface	Output
4	SWDIO	Data pin for JTAG interface	I/O
5	NRST	Reset pin for JTAG interface	Input
6	GND	GND	Output
7	IO_8	WKup,ADC,Timer,Event,I/O	TTL signal voltage is 3.3V
8	REST	Reset	TTL signal voltage is 3.3V
9	IO_0	ADC,DAC,Timer,Event,I/O	TTL signal voltage is 3.3V
10	IO_1	ADC,Timer,Event,I/O	TTL signal voltage is 3.3V
11	IO_2	ADC,Timer,Event,I/O	TTL signal voltage is 3.3V
12	IO_3	RST,Timer,Event,I/O	TTL signal voltage is 3.3V
13	IO_4	RST,Timer,Event,I/O	TTL signal voltage is 3.3V
14	IO_5	ADC,Timer,Event,I/O	TTL signal voltage is 3.3V
15	IO_6	RST,Timer,Event,I/O	TTL signal voltage is 3.3V
16	IO_7	RST,ADC,Event,I/O	TTL signal voltage is 3.3V

 

Display Usage

Functional description

Smart Display can be used to display the coordinate, status and data information provided by the connected HOST device. Customers can configure the position coordinates they want to display in normal operation mode (Node ID = 0x7B).

The Display is designed to be easily connected to a controller network, and to operate with minimum setup or knowledge of the SDO configuration on the controllers.

Splash Screen

The default splash image is shown below:

 

This product is produced as a generic product. If you require a custom splash image for your application, contact us to discuss.

Default Selection

Press the preferred application and hold for 3 seconds for the first time power on.
 

 

Example Screen Layout (Industry application)

The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in an industry application situation.

Example Screen Layout (Vehicle automotive)

The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in a vehicle automotive situation.

Example Screen Layout (Medical application)

The screen layout described in this section is intended to demonstrate the settings of screen items that can be used in a Medical application situation.

EVALUATION KIT 

Evaluation Kit P/N WWSSDEMO101J-AA-30# available at the links: ITA: https://www.first-components.com/it/wwssdemo101j-aa-30 ENG: https://www.first-components.com/en/wwssdemo101j-aa-30