Cerca
Filters
Close

WEO12864W#ACP3N00000-FC

PMOLED 0.96'' Graphic 128x64, White color, COG, 3V, Interface 6800,8080,SPI,I2C, SSD1315 IC, Low thickness without Sponge, Glare (FPC per Soldering)

DESCRIPTION

Winstar released a 0.96 inch Thin OLED Display model (1.26mm thickness) which is made of 128x64 pixels, diagonal size only 0.96 inch. The new version thin 0.96" OLED display is also built-in SSD1315 driver IC; it communicates via 6800/8080 8-bit parallel and I2C/SPI interface.

DRAWING


SPECIFICATIONS

Interface Pin Function

No.SymbolFunction
1 N.C. (GND) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2 C2N C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
3 C2P
4 C1P
5 C1N
6 VBAT This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used.
7 NC NC
8 VSS Ground pin. It must be connected to external ground.
9 VDD Power supply pin for core logic operation.
10 BS0 These pins are MCU interface selection input. See the
following table:
 BS0BS1BS2
I2C 0 1 0
3-wire SPI 1 0 0
4-wire SPI 0 0 0
8-bit 68XX Parallel 0 0 1
8-bit 80XX Parallel 0 1 1
11 BS1
12 BS2
13 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
14 RES# This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
15 D/C# This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDD), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams of IC SPEC.
16 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E/RD# When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDD) and the chip is selected.
When connecting to an 8080-series microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
18~25 D0~D7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
26 IREF When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA.
27 VCOMH The pin for COM signal deselected voltage level. A capacitor should be connected between this pin and VSS.
28 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
29 VLSS This is an analog ground pin. It should be connected to VSS externally.
30 NC
(GND)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

 

General Specification

ItemDimensionUnit
Dot Matrix 128 x 64
Module dimension 26.70 × 19.26 ×1.26 mm
Active Area 21.74 × 10.86 mm
Pixel Size 0.15 × 0.15 mm
Pixel Pitch 0.17 × 0.17 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/64 Duty
Controller IC SSD1315
Interface 6800, 8080, SPI, I2C
Size 0.96 inch

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage for Logic VDD 0 4.0 V
Charge Pump Regulator Supply Voltage VBAT 0 6.0 V
Supply Voltage for Display VCC 0 15.0 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C

 

Electronical Characteristics

DC Electrical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD 1.65 3.0 3.3 V
Charge Pump Regulator Supply Voltage VBAT 2.4 3.5 5.0 V
Supply Voltage for Display VCC 6.0 12.0 12.5 V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC) Charge Pump
VPP
7.0 7.5 V
Input High Volt. VIH 0.8xVDD VDD V
Input Low Volt. VIL 0 0.2xVDD V
Output High Volt. VOH 0.9xVDD VDD V
Output Low Volt. VOL 0 0.1xVDD V
Operating Current for VCC (50% display ON) (VCC Supplied Externally) ICC VCC=12V 10 20 mA
50% checkerboard operating Current (VCC Generated by Internal DC/DC) IBAT 15 30 mA


SKU: WEO12864W#ACP3N00000-FC
Brand: Winstar
Disponibile: No
Prezzi per quantità
Quantità
1+
5+
10+
25+
Prezzo
€5,00
€3,70
€3,60
€3,50

Per quantita’ maggiori di 25pz prego invii la richiesta a sales@first-components.com o chiami il +39 0332 1888005

€5,00 IVA esclusa

DESCRIPTION

Winstar released a 0.96 inch Thin OLED Display model (1.26mm thickness) which is made of 128x64 pixels, diagonal size only 0.96 inch. The new version thin 0.96" OLED display is also built-in SSD1315 driver IC; it communicates via 6800/8080 8-bit parallel and I2C/SPI interface.

DRAWING


SPECIFICATIONS

Interface Pin Function

No.SymbolFunction
1 N.C. (GND) The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.
2 C2N C1P/C1N – Pin for charge pump capacitor; Connect to each other with a capacitor.
C2P/C2N – Pin for charge pump capacitor; Connect to each other with a capacitor.
3 C2P
4 C1P
5 C1N
6 VBAT This is the power supply pin for the internal buffer of the DC/DC voltage converter. It must be connected to external source when the converter is used. It should be float when the converter is not used.
7 NC NC
8 VSS Ground pin. It must be connected to external ground.
9 VDD Power supply pin for core logic operation.
10 BS0 These pins are MCU interface selection input. See the
following table:
 BS0BS1BS2
I2C 0 1 0
3-wire SPI 1 0 0
4-wire SPI 0 0 0
8-bit 68XX Parallel 0 0 1
8-bit 80XX Parallel 0 1 1
11 BS1
12 BS2
13 CS# This pin is the chip select input connecting to the MCU.
The chip is enabled for MCU communication only when CS# is pulled LOW (active LOW).
14 RES# This pin is reset signal input. When the pin is low, initialization of the chip is executed. Keep this pin HIGH (i.e. connect to VDD) during normal operation.
15 D/C# This is Data/Command control pin. When it is pulled HIGH (i.e. connect to VDD), the data at D[7:0] is treated as data. When it is pulled LOW, the data at D[7:0] will be transferred to the command register.
In I2C mode, this pin acts as SA0 for slave address selection.
When 3-wire serial interface is selected, this pin must be connected to VSS.
For detail relationship to MCU interface signals, please refer to the Timing Characteristics Diagrams of IC SPEC.
16 R/W# This is read / write control input pin connecting to the MCU interface.
When interfacing to a 6800-series microprocessor, this pin will be used as Read/Write (R/W#) selection input. Read mode will be carried out when this pin is pulled HIGH (i.e. connect to VDD) and write mode when LOW.
When 8080 interface mode is selected, this pin will be the Write (WR#) input. Data write operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
17 E/RD# When interfacing to a 6800-series microprocessor, this pin will be used as the Enable (E) signal.
Read/write operation is initiated when this pin is pulled HIGH (i.e. connect to VDD) and the chip is selected.
When connecting to an 8080-series microprocessor, this pin receives the Read (RD#) signal. Read operation is initiated when this pin is pulled LOW and the chip is selected.
When serial or I2C interface is selected, this pin must be connected to VSS.
18~25 D0~D7 These are 8-bit bi-directional data bus to be connected to the microprocessor’s data bus.
When serial interface mode is selected, D0 will be the serial clock input: SCLK; D1 will be the serial data input: SDIN.
When I2C mode is selected, D2, D1 should be tied together and serve as SDAout, SDAin in application and D0 is the serial clock input, SCL.
26 IREF When external IREF is used, a resistor should be connected between this pin and VSS to maintain the IREF current at a maximum of 30uA.
27 VCOMH The pin for COM signal deselected voltage level. A capacitor should be connected between this pin and VSS.
28 VCC Power supply for panel driving voltage. This is also the most positive power voltage supply pin.
When charge pump is enabled, a capacitor should be connected between this pin and VSS.
29 VLSS This is an analog ground pin. It should be connected to VSS externally.
30 NC
(GND)
The supporting pins can reduce the influences from stresses on the function pins. These pins must be connected to external ground.

 

General Specification

ItemDimensionUnit
Dot Matrix 128 x 64
Module dimension 26.70 × 19.26 ×1.26 mm
Active Area 21.74 × 10.86 mm
Pixel Size 0.15 × 0.15 mm
Pixel Pitch 0.17 × 0.17 mm
Display Mode Passive Matrix
Display Color Monochrome
Drive Duty 1/64 Duty
Controller IC SSD1315
Interface 6800, 8080, SPI, I2C
Size 0.96 inch

 

Absolute Maximum Ratings

ParameterSymbolMinMaxUnit
Supply Voltage for Logic VDD 0 4.0 V
Charge Pump Regulator Supply Voltage VBAT 0 6.0 V
Supply Voltage for Display VCC 0 15.0 V
Operating Temperature TOP -40 +80 °C
Storage Temperature TSTG -40 +85 °C

 

Electronical Characteristics

DC Electrical Characteristics

ItemSymbolConditionMinTypMaxUnit
Supply Voltage for Logic VDD 1.65 3.0 3.3 V
Charge Pump Regulator Supply Voltage VBAT 2.4 3.5 5.0 V
Supply Voltage for Display VCC 6.0 12.0 12.5 V
Charge Pump Output Voltage for Display (Generated by Internal DC/DC) Charge Pump
VPP
7.0 7.5 V
Input High Volt. VIH 0.8xVDD VDD V
Input Low Volt. VIL 0 0.2xVDD V
Output High Volt. VOH 0.9xVDD VDD V
Output Low Volt. VOL 0 0.1xVDD V
Operating Current for VCC (50% display ON) (VCC Supplied Externally) ICC VCC=12V 10 20 mA
50% checkerboard operating Current (VCC Generated by Internal DC/DC) IBAT 15 30 mA


Specifiche di prodotto
Brand Winstar
Size 0.96"
Risoluzione 128x64
Area Attiva (mm) 21.73x10.85
Dot Size 0.14x0.14
Polarizzatore Glare
Colore White
Alimentazione 3V
Interfaccia Display 6800/8080/SPI/I2C
Display IC SSD1315
Struttura Costruttiva COG
Frame No
Touch Panel No touch
Temperatura O. (°C) -40~80
Connessione Display FPC per Soldering
Nr. Pin 30
Passo Pin 0.7mm
Preferred - Not Preferred Preferred
Download
Specifiche di prodotto
Brand Winstar
Size 0.96"
Risoluzione 128x64
Area Attiva (mm) 21.73x10.85
Dot Size 0.14x0.14
Polarizzatore Glare
Colore White
Alimentazione 3V
Interfaccia Display 6800/8080/SPI/I2C
Display IC SSD1315
Struttura Costruttiva COG
Frame No
Touch Panel No touch
Temperatura O. (°C) -40~80
Connessione Display FPC per Soldering
Nr. Pin 30
Passo Pin 0.7mm
Preferred - Not Preferred Preferred
;