Cerca
Italiano
Catalogo
    Menu Chiudi

    WF24-240320LS#0P0B-FC

    TFT 2.4" 240x320 Portrait LCD Panel, Interface MCU (Parallel/SPI) IC ILI9341V, 500cd/m², Wide View Angle (IPS), No touch, Anti-Glare surface
    Brand: Winstar
    Cod.: WF24-240320LS#0P0B-FC

    Kit accessori

    Prezzi per quantità
    Quantità
    1+
    5+
    10+
    25+
    Prezzo
    €14,90
    €13,40
    €12,60
    €12,30

    Per quantità maggiori di 49pz prego invii la richiesta a [email protected] o chiami il +39 0332 1888005

    Disponibilità: Disponibile
    €14,90 IVA esclusa
    i h

    DESCRIPTION

    2.4 inch IPS TFT-LCD display module; made of resolution 240 x 320 pixels. This module is built in with ILI9341V controller IC, it supports MCU8080 and SPI interface, it featured with IPS panel which is having the advantages of wider viewing angle of Left:80 / Right:80 / Up:80 / Down:80 degree (typical), contrast ratio 800 (typical value), brightness 500 nits (typical value), Anti-Glare surface panel. 

    This 2.4 inch TFT- LCD display is portrait mode; it integrated controller IC ILI9341V on module, Supply Voltage for Analog (VCI) from 2.5V to 3.3V. Operating temperatures from -20℃ to +70℃; storage temperatures from -30 to +80 ℃.

     

    DRAWING

     

    SPECIFICATIONS

     

    Interface Pin Function

    NOSymbolFunctionI/O
    1 GND Ground P
    2-6 NC No connection -
    7 VCI High voltage power supply for analog circuit blocks
    (2.5 ~ 3.3 V)
    P
    8 IOVCC Low voltage power supply for interface logic circuits
    (1.65 ~ 3.3 V)
    P
    9 TE Tearing effect output pin to synchronize MPU to frame writing, activated by S/W command. When this pin is not activated, this pin is low.
    If not used, open this pin.
    O
    10 CS Chip select signal. I
    11 D/CX(SCL) (D/CX): This pin is used to select “Data or Command” in the parallel interface.
    When DCX = 1, data is selected.
    When DCX = 0, command is selected.
    (SCL): This pin is used as the serial interface clock in 3-wire 9-bit/4-wire 8-bit serial data interface.
    If not used, this pin should be connected to VDDI or VSS.
    I
    12 WR(SPI_D/C) (WRX) - 8080-Ⅰ/8080-Ⅱ system: Serves as a write signal and writes data at the rising edge.
    (D/CX) - 4-line system: Serves as the selector of command or parameter.
    Fix to VDDI level when not in use.
    I
    13 RD 8080-Ⅰ/8080-Ⅱ system (RDX): Serves as a read signal and MCU read data at the rising edge.
    Fix to VDDI level when not in use.
    I
    14-29 DB0~DB15 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
    30 RESET This signal will reset the device and must be applied to properly initialize the chip.
    Signal is active low.
    I
    31 IM0 Select the MCU interface mode

    MPU Parallel interface bus and serial interface select
    If use RGB Interface must select serial interface.
    * : Fix this pin at VDDI or VSS.
    I
    32 IM1
    33 IM2
    34 DB16 18-bit parallel bi-directional data bus for MCU system and RGB interface mode Fix to VSS level when not in use. I/O
    35 DB17
    36 LEDK Cathode of LED backlight. P
    37 LEDK Cathode of LED backlight. P
    38 LEDA Anode of LED backlight. P
    39 SDI(SDA) When IM[3] : Low, Serial in/out signal.
    When IM[3] : High, Serial input signal.
    The data is applied on the rising edge of the SCL signal.
    If not used, fix this pin at VDDI or VSS.
    I/O
    40 SDO Serial output signal.
    The data is outputted on the falling edge of the SCL signal.
    If not used, open this pin
    O

     

    General Specifications

    ItemDimensionUnit
    Size 2.4 inch
    Dot Matrix 240 × RGB × 320(TFT) dots
    Module dimension 42.72(W) × 60.26(H) × 2.8(D) mm
    Active area 36.72 × 48.96 mm
    Dot pitch 0.153 × 0.153 mm
    LCD type TFT, Normally Black, Transmissive
    Controller IC ILI9341V or equivalent
    Viewing angle 80/80/80/80
    Aspect Ratio Portrait
    Backlight Type LED, Normally White
    Touch Panel Without Touch Panel
    Surface Anti-Glare

     

    Absolute Maximum Ratings

    ItemSymbolMinTypMaxUnit
    Operating Temperature TOP -20 - +70 ℃
    Storage Temperature TST -30 - +80 ℃

     

    Electrical Characteristics

    ItemSymbolMinTypMaxUnit
    Supply Voltage For Analog VCI 2.5 — 3.3 V
    Supply Voltage For Logic IOVCC 2.5 — 3.3 V
    Supply Current For LCM ICI — 6 9 mA
    Specifiche di prodotto
    Size 2.4"
    Resolution 240x320
    Active Area (mm) 36.72x48.96
    Color Full Color
    Display Interface MCU (Parallel/SPI)
    Display IC ILI9341V
    View Angle IPS
    Frame No
    Touch Panel No touch
    O. Temperature (°C) -20~70
    Data Connection FPC for ZIF Connector
    Pin Nr. 40
    Pin Pitch 0.5mm
    Preferred - Not Preferred Preferred
    You are running a Trial version of Nop Attachments
    *
    *
    *
    *
    Solo gli utenti registrati possono scrivere recensioni